INSTALLATION MANUAL Arlo™ Single Handle Vessel Faucet KBF-1200 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List G A H I B C D J E F A. Faucet Body B. Plastic Washer C. Metal Washer D. Nut & Screws E. Waterlines 4 F. Flange & Washer G. Aerator H. Aerator Key I. Hex Wrench J.
Faucet Dimensions 6 3/4" [171mm] 5" [128mm] 12 1/8" [307mm] 8 1/8" [208mm] 2 1/4" [56mm] 2 1/2" [64mm] 3/8" compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1: Remove washers and nut Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove the plastic washer (B), metal washer (C) and nut & screws (D) from the faucet (A). A B C D Step 2: Installing the faucet A F Before installation, ensure that the flange (F) is placed on the bottom of the faucet assembly (A). Place the faucet (A) through the hole in the countertop.
Step 3: Connect waterlines to main valve Attach waterlines (E) to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON). E Step 4: Install Press pop-up assembly 1 2 Unscrew the nut (6) from the pop-up body (2), move over the tail pipe (7) and washer (5), then unscrew the coupling nut (4) and remove the washer (3).
Step 4: Install Press pop-up assembly - continued 1 2 3 Place the washer (1) underneath the flange of the pop-up body (2). Slide the pop-up body (2) down through the drain hole on the vessel or basin sink. From the underside of the sink, slide the washer (3) against the bottom of the vessel or basin sink, thread on the coupling nut (4) and tighten. Do not overtighten. 279 10 31/32” 217 8 17/32” Slide the nut (6) over the tail pipe (7). Place the washer (5) into the nut and tighten. Do not overtighten.
Replacement Parts 2 3 1 15 4 815 32 3/32” Finish / Color 1. Cover Button GR, BL* 2. Set Screw 4. Cap 7 5. Bonnet Nut 1 2 KP27046 CH, SFS, ORB, MB BG* KP27048 3 6. Screw Ø35~Ø38 Ø1 3/8~Ø1 1/2” 9 10 11 12 an s th Les m 90m 16 13 KP27049 KP27047 KP27050 8. Aerator 4 9. Aerator Key 6 10. Plastic Washer 8 14 KP27002 CH, SFS, ORB, MB BG* Ø35~Ø38 7. Cartridge Ø1 3/8”~Ø1 1/2” 8 Part # KP27001 3. Handle 5 6 194 7 5/8” Replacement Parts List 5 7 KP27051 KP27052 KP27146 11.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle. Bonnet nut (5) has come loose. Remove the index (1). Loosen set screw (2) with hex wrench (15). Remove the handle (3). Unscrew cap (4) (by hand only). Tighten bonnet nut (5) with an adjustable wrench. Aerator drips or has inconsistent water flow pattern.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI/CAN 61: Q ≤ 1 UP C R C NSF/ANSI 61 C R ASME A112.18.1 1.2GPM 4.5L/min maximum Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.