R INSTALLATION MANUAL Kore Workstation Stainless Steel Farmhouse Kitchen Sinks KWF210-30, KWF210-33, KWF210-33/PGM, KWF210-36 KWF410-30, KWF410-33, KWF410-33/PGM, KWF410-36 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Inspect the sink prior to installation to make sure the sink has not been damaged during shipping · Use the cut-out template provided by Kraus · Observe all plumbing and building codes according to your state requirement · Additional floor and wall preparation may be required to avoid damaging the product · Make sure to purchase the correct cabinet for your farmhouse sink.
Parts List KWF210-30 · · · · · · · Cut-Out Template Mounting Hardware Bottom Grid KBG-UN1-30 Strainer ST-1 Drain Cap STC-2 Rolling Mat KRM-11BL Cutting Board KCB-WS103BB KWF210-33 · · · · · · · Cut-Out Template Mounting Hardware Bottom Grid KBG-UN1-33 Strainer ST-1 Drain Cap STC-2 Rolling Mat KRM-11BL Cutting Board KCB-WS103BB KWF210-33/PGM · · · · · · · Cut-Out Template Mounting Hardware Bottom Grid KBG-UN1-33/PGM Strainer ST-1/PGM Drain Cap STC-2/PGM Rolling Mat KRM-11BL Cutting Board KCB-WS103AC KW
Dimensions: 20 1/4" (514.4mm) 19 1/2" (495.3mm) 16" (406.4mm) 17" (431.8mm) (254mm) 10" 5" 9" (228.6mm) 1" 9 1/2" (241.3mm) 10" 20 1/4" (514.4mm) 19 1/2" (495.3mm) 17" (431.8mm) 16" (406.4mm) 20 1/4" (514.4mm) 19 1/2" (495.3mm) 17" (431.8mm) 10" (254mm) (228.6mm) 5" 9" (90mm) 16" (406.4mm) (127mm) (127mm) 1" (25.4mm) Model #: KWF210-33 & KWF210-33/PGM Sink Dimensions: 32 7/8” x 20 1/4” x 10” Min Cabinet Size: 36” 35 7/8" (911.2mm) 34" (863.
17" (431.8mm) 20 1/4" (514.4mm) 10 1/2" (265.5mm) (228.6mm) 9" 9 1/2" (241.3mm) 10 1/2" (265.5mm) (254mm) (228.6mm) R1/8" (3mm) (254mm) 16" (406.4mm) 5" (57.2mm) 10" 2 1/4" (127mm) 1" (90mm) R1/8" 9" (241.3mm) 9 1/2" Model #: KWF410-33 & KWF410-33/PGM Sink Dimensions: 32 7/8” x 20 1/4” x 10” Min Cabinet Size: 36” 35 7/8" (911.2mm) 34" (863.6mm) 5" 20 1/4" (514.4mm) 2 1/4" (57.2mm) 17" (431.8mm) (90mm) 5" 3 1/2" 16" (406.
Step 1. Determine Reveal Type · Use scissors to cut along the line of the paper template for your desired reveal type (Negative, Positive, or Flushed Reveal) KRAUS Recommended Installation Type 3/8” Positive Reveal 3/8” Positive Flushed/Zero Reveal Centerline Flushed/Zero Step 2. Position Template · · Check the cut-out template against the actual sink to ensure a proper sized cut-out. Place the cut-out template in the desired location on the countertop.
Step 3. Trace Template · Trace template on countertop with a pencil. Step 4. Cut Countertop · Cut the opening in the countertop by carefully following the traced line. NOTE: Please use the appropriate saw that best fits your countertop material.
Step 5. Cut Cabinet Front · Measure height of apron front. Add 1/16" to the dimension when you mark base cabinet front cutout. Use jigsaw to cut. Step 6. Set Up Mounting Brackets · · Turn countertop over and align sink with countertop. Decide location for mounting brackets. Mounting holes should be 1/2" from edge of sink.
Step 7. Drill Hole in Countertop · Drill 3/8" diameter x 1/2" deep hole in the countertop.
Step 8. Install Anchors · Insert anchors into drilled holes and lightly tap with a hammer until flush.
Step 9. Secure Sink to Countertop · Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly.
Step 10. Attach Mounting Hardware · · Attach mounting hardware to secure bowl. Remove excess sealant from inside lip. Allow sealant to set for 30 - 60 minutes. NOTE: Use acetone or rubbing alcohol to remove any excess sealant.
Step 11. Install Plumbing Fixtures · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks.
Codes/Standards Applicable UP C C R Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Kitchen Sink" in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
