4- Precision Band Saw Fence KMS7200 INSTRUCTIONAL MANUAL The Blue Mark of Quality.
Table of Contents Congratulations on choosing a Kreg Precision Band Saw Fence! Be sure to read the instructions and the safety warnings completely before using this tool.
2 Safety Guidelines 4- Precision Band Saw Fence Guidelines Thank you for purchasing KREG components. All products have been designed to ensure safe and efficient operation when installed and used properly. We think you will agree that our Precision Band Saw Fence is the best currently available. Warning - Woodworking machines are dangerous and can cause personal injury if not used properly. - Read safety instructions and operating instructions for your machine completely before using products.
Safety Guidelines 3 Safety Guidelines To avoid injury, never adjust the fence along the mounting rail or position of the HD Trak while the band saw is running. Make sure the blade comes to a complete stop before removing the workpiece. Ground all tools. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If an adapter is used to accommodate a two-prong receptacle, the adapter lug must be attached to a known ground. Never remove the third prong.
4 Parts Diagram FT4136 FT4175 FT4137 DK1313 FT4047 DK1504 FT4138 FT4144 FT4064 FT4025 FT4140 FT4142 FT4185 (Delta) FT4146 (Jet, Craftsman, Ridgid, Import) DK1504 FT4143 FT4063 FT4176 Part Number DK1313 DK1504 FT4025 FT4047 FT4063 FT4064 FT4136 FT41 37 FT4138 FT4140 FT4142 FT4143 FT4144 FT4185 FT4146 FT4175 FT4176 Quantity 2 4 2 1 1 1 1 2 2 2 1 1 1 2 2 2 1 Description Black T-Knob 1/4” Brass Washers 1/4-20 x 3/4” Nylon Set Screw Right to Left Reading Self-Adhesive Tape Lens Cursor 10-32 x 1/4”
Installing the Mounting Rail Installing the Mounting Rail Choose the set of slots that corresponds to the band saw where you are installing the Band Saw Fence. Vertical slots are used so that the fence rail can be properly aligned with several different band saws with holes in their tables at different heights in relationship with the table surface. Refer to Fig. 1 to see which slots are for your saw.
6 Another pair of larger set-screws is located toward the rear of the Clamp Block and these set-screws can be adjusted to maintain parallelism between the HD Trak and the blade. The Adapter Bracket transfers the horizontal clamping action along the Mounting Rail to the vertical surface of the HD Trak and the fence itself. The Adapter Bracket is machined so that it will allow the user to adjust the Band Saw Fence for blade drift.
7 Figure 3 1/4” Brass Washer Black T-Knob Adapter Bracket 1/4”x2-1/2” Hex Bolts Band Saw Trak Clamp Block Lock Down Knob Attaching the Band Saw Trak Refer to Fig. 3 The Trak attaches to the Clamp Block via the Adapter Bracket. These parts are designed in such a way that the fence may be used on either side of the blade. In addition to this feature the Trak may be positioned anywhere along the Adapter Bracket.
8 Attaching the Tape The Measuring Tape on the Kreg Precision Band Saw Fence will transform your band saw into a woodworking machine capable of exact cuts and repeatable accuracy. 1. Position the fence against the blade making sure the fence is touching but not deflecting the blade. 2. Use a pencil to scribe a line on the Mounting Rail above and below the red line on the Lens Cursor.
9 Adjusting for Blade Drift The Kreg Precision Band Saw Fence will allow the user to align the fence to match a saw blade’s “drift angle”. You can set the fence to compensate for the drift angle by adjusting the Fence “out of square” with the Clamp Block. Remove the Fence and Clamp Block assembly as described in the previous section. Using a piece of scrap material about 30” long cut to middle of the scrap board. Turn off the saw and hold the scrap board firmly while the saw coasts down.
10 WARRANTY KREG PRECISION BAND SAW FENCE Kreg Tool Company warrants to its authorized distributors of Kreg products and the original purchasers from such distributors, the Kreg Precision Band Saw Fence to be free of defects in materials and workmanship for a period of one (1) years from the date of delivery to the original purchaser. During said warranty period Kreg will, at its option, repair or replace any product (or component part thereof) proving defective during said period.
11 4- 4-