S–300i Remote Control Integrated Amplifier Instructions for Use Owner’s Reference
S-300i Remote Control Integrated Amplifier Instructions for Use v 1.0 CONTACT INFORMATION Krell Industries, Inc. 45 Connair Road Orange, CT 06477-3650 USA TEL 203-799-9954 FAX 203-891-2028 E-MAIL krell@krellonline.com WEBSITE http://www.krellonline.com WARNINGS Do not place the integrated amplifier where it could be exposed to dripping or splashing. The ventilation grids on the top and bottom of the S-300i must be unobstructed at all times during operation.
Contents Page Krell S-300i INTRODUCTION 1 DEFINITION OF T E R M S 2 UNPACKING 4 PLACEMENT AC Power Guidelines Power Cord 5 5 5 FRONT PANEL / REMOTE CONTROL DESCRIPTION 7 REMOTE CONTROL ONLY Battery Installation and Removal Remote Control Only Functions 9 9 9 BACK PANEL DESCRIPTION 12 CONNECTING THE S-300i TO YOUR SYSTEM Connection Steps 14 14 OPERATING YOUR S-300i Amplifier Operation 15 15 OPTIONAL CONFIGURATIONS Configuring the S-300i Balance Input Balance Trim Input Level Trim Theater
Illustrations Page FIGURE 1 The S-300i Front Panel 6 FIGURE 2 The S-300i Remote Control 6 FIGURE 3 The S-300i Back Panel iv 11 Krell S-300i
Introduction Thank you for your purchase of the Krell S-300i Remote Control Integrated Amplifier. This fully integrated amplifier and preamplifier has a discrete signal path from input to output and employs a wide bandwidth design with low negative feedback for sonic accuracy throughout the frequency spectrum. All circuits up to the driver stage are balanced and pure Class A.
Definition of Terms Following are the definitions of key terms used in your owner’s reference manual. CONFIGURATIONS Theater Throughput Theater Throughput is a Krell configuration option that allows the signal from a surround preamp/processor to pass through a Krell preamplifier or integrated amplifier with no gain, for integrated volume and balance management of Krell home theater systems.
Definition of Terms, continued OPERATION Off The component is off when the rear panel button is not depressed. Stand-by Mode A low power consumption status that keeps the audio circuits at idle. When you press the rear panel power button, the red standby LED illuminates. The component is now ready to be switched to the operational mode. Krell recommends leaving the component in the stand-by mode when it is not playing music.
Unpacking Follow these steps to safely unpack the S-300i: 1. Open the shipping box and remove the top layer of foam. T h e S-300i and the S-300i accessory kit containing the following items are visible: 1 1 1 1 AC power cord S-300i remote control 30-Pin iPod connection cable packet containing the Quick Setup Guide and the warranty registration card 2. Grasp the underside of the amplifier and lift it straight out of the packing box. 3.
Placement Before you install the S-300i into your system, review the following guidelines to choose the location for the S-300i. This will facilitate a clean, trouble-free installation. The S-300i does not require any type of special rack or cabinet for installation. For the dimensions of the S-300i, see Specifications, on the back cover. Place the S-300i on a firm, level surface, away from excessive heat, humidity, or moisture. The S-300i requires at least 1 inch (2.
F i g u re 1 The S-300i Front Panel Power 1 Power BUTTON 2 Power LED 3 Infrared Sensor Input Devices 5 S-1, S-2, S-3, B-1 and iPod Buttons or Keys 7 Volume Level Knob or Level / Navigation Keys Mode Control 6 MENU Button or Key 8 ENTER Button or Key 9 Display Wi n d o w 12 F i g u re 2 The S-300i Remote Contro l Direct iPod control keys Volume Adjustment Functions 10 Bal (Balance) Keys (Remote) Buttons for other KRELL products 11 Amp option select 13 CD/ DVD transport control Note 6 Some remote con
Front Panel/Remote Control Description See Figures 1 and 2 on page 6 Power, analog input selections, and volume control accessed via the front panel of the S-300i are described in the illustration legend below. The front panel display shows volume and balance levels, and Theater Throughput status. Most front panel features can also be activated via the keys on the remote.
Front Panel Description, continued MODE INDICATORS 7 Level Knob / Level Keys The level knob on the front panel or the level keys on the remote control adjust the amplifier output level. The output level is indicated numerically on the front panel display, with a range from 0-151.
Remote Control Only See Figure 2 on page 6 B a t t e ry Installation and Removal The S-300i remote control uses two AAA alkaline batteries, which are included with the shipment. To open the battery compartment on the back of the remote control: 1. Place the remote face down on the table. 2. Use T-8 Torx wrench to remove the bottom cover. Note Do not use a knife or other sharp objects to open the battery compart ment; they will scratch the remote control finish. 3.
Remote Control Functions, continued VOLUME ADJUSTMENT FUNCTION 12 Direct iPod Functions With an iPod connected to the special 30-pin connector, basic control functions are available from the remote control.
Figure 3 The S-300i Back Panel Amplifier Channel Outputs 14 Left and Right Loudspeaker Outputs Analog Inputs 15 Left and Right Balanced Analog Inputs 16 Left and Right Singleended Analog Inputs 17 Direct iPod Input Analog Outputs 19 Left and Right Preamp Outputs Remote Connections 18 RS-232 control Port 20 RC-5 In 21 12 VDC Trigger In/Out Power 22 IEC Connector 23 Line Fuse 24 Main Power Button Krell S-300i 11
Back Panel Description See Figure 3 on page 11 The S-300i back panel provides connections for all inputs and outputs, power on/off, and additional remote connections. AMPLIFIER CHANNEL OUTPUTS 14 Left and Right Loudspeaker Outputs The S-300i is equipped with standard binding posts for each amplifier channel. These connectors accept bare wire, pins, banana plugs, or spade lugs. Use the red terminal for the positive connection and the black terminal for the negative connection.
Back Panel Description, continued Out. The output sends 12 VDC (12 V trigger) power on/off signals to other Krell components and other devices that incorporate a 12 V trigger. Notes I n .The input receives 12 VDC (12 V trigger) power on/off signals from other Krell components and other devices that incorporate a 12 V trigger. POWER The 12 VDC output current is limited to 30 ma.
Connecting the S-300i to Your System USING BALANCED CONNECTIONS Krell recommends using balanced interconnect cables. Balanced interconnect cables not only can minimize sonic loss but are also immune to induced noise, especially with installations using long cables. Balanced connections have 6 dB more gain than singleended connections. When level matching is critical, keep this gain value in mind. Connection Steps Follow these steps to connect the S-300i to your system. 1.
Operating Your S-300i This section provides information about operating the S - 3 0 0 i. The S-300i provides input selection,volume control operation and any of the various menu functions via the front panel. The remote control includes additional source, preamp and amplifier functions as well. See Remote Control Only, on page 9, for more information. After the S-300i is connected to AC power and in the stand-by mode, use the power button or key (1) to switch the component to the operational mode.
Operating Your S-300i, ON/OFF AND STAND-BY OPERATION, continued continued 3. Start playing the source. 4. Set the volume to a comfortable listening level using the level knob on the front panel or the level keys on the remote control (7). 5. To turn the amplifier off, press the power button on the front panel or the power key on the remote control (1). The red stand-by LED (2) illuminates. It is now safe to turn off the rest of the system.
Optional Configurations Customizing the S-300i The S-300i menu allows you to configure the following functions. You can also use the menu to review version information about the software. Navigation Conventions Navigating the S-300i menu is straightforward and consistent throughout. (6) Menu Button or Key To enter the menu, press the menu button on the preamplifier front panel or the menu key on the remote control. Once you are in the menu, you can press the menu button or key to exit the menu.
Optional Configurations, continued Menu Features and Functions Balance This function enables you to adjust the balance between the left and right output channels. The options are: CENTER, Left 1-5dB, Right 1-5 dB,All Left, or All Right. The remote control has direct (10) keys to make these adjustments. For front panel adjustment follow the steps listed below. Enter the menu, then: 1. Use the level control knob on the preamplifier front panel or to select: BALANCE. 2.
Optional Configurations, continued 6. Press the level control knob or key to confirm the selection. The front panel display reads: INPUT BALANCE TRIM. Input Level Trim This function enables you to select a GAIN offset individually for a particular input. The options are: +/-6 dB, in 1 dB increments. Enter the menu, then: 1. Use the level control knob on the preamplifier front panel or the up and down keys (7) on the remote control to select: INPUT LEVEL TRIM.
Optional Configurations, continued 3. Use the level control knob or the Volume up and down keys to select the desired input: S-1, S-2, S-3 or B-1. 4. Press the enter button or key to confirm the selection. S-1, S-2, S-3 or B-1 The selected input is set to THEATER and the volume control is disengaged for that input on the S-300i. OFF ALL inputs are configured normally and the volume control is engaged for all inputs on the S-300i.
Optional Configurations, continued 7. Press the level control knob or key. The front panel display shows the default mode: HIGH. 8. Use the level control knob or the volume up and down keys to select the desired brightness: LOW, MED, or HIGH. 9. Press the level control knob or key to confirm the selection. The front panel display reads: BRIGHTNESS. ON The front panel display is always on. TIMED The front panel display turns off after 30 seconds. BRIGHTNESS Controls the brightness of the display.
Optional Configurations, continued Enter the menu, then: 1. Use the level control knob on the preamplifier front panel or the up and down keys on the remote control to select: INPUT TRIGGER. 2. Press the level control knob on the preamplifier front panel or the enter key (8) on the remote control. The front panel display (9) shows the last input trigger setting. the default mode is: NORMAL. 3. Use the level control knob or the up and down keys to select the desired option: OFF, NORMAL, or THEATER. 4.
Optional Configurations, continued Input Name Options 4. Select DELAY. You are prompted to enter a delay time of 0-30 seconds. 5. Enter the delay time. 6. Press enter to confirm the selection. The display reads: DELAY. 7. Use the level control knob or volume up and down keys to scroll to: BACK.
Optional Configurations, continued ON The S-300i turns on automatically, remaining in stand-by mode only for a brief warm-up period, when ac power is applied. Input Name This function enables you to select a device name for each input. The input name options are listed in the left margin, on this page. Enter the menu, then: 1. Use the level control knob on the preamplifier front panel or up and down keys (14) on the remote control to select: INPUT NAME. 2.
Optional Configurations, continued Configuration This function enables you to access factory default settings or your own saved settings. The options are: RECALL, SAVE, or FACTORY DEFAULT. Enter the menu, then: 1. Use the level control knob on the preamplifier channel front panel or up and down keys (7) on the remote control to select: CONFIGURATION. 2. The front panel display (9) shows the default mode: FACTORY DEFAULT. 3.
How to Troubleshoot System Noise AC grounding becomes critical when connecting high performance audio components. When you mix and match audio components, each with its own ground potential, a low frequency hum may occur in one or both loudspeakers. This sometimes occurs when introducing a new component into a system. If a low frequency hum emanates from the loudspeakers when you place the S-300i amplifier into the system, follow these simple troubleshooting steps: 1.
Questions and Answers Q. Should I leave myS - 3 0 0 i on at all times? A. Krell recommends leaving the amplifier in the stand-by mode, ready to play music. If you are not going to play music for a long time, you may turn off the rear panel power button. Q. When I turn on the amplifier there is a loud hum through the loudspeakers. What should I do? A. When a new component is introduced into a system, a low frequency hum may occur in one or both loudspeakers.
Warranty To register your product for warranty benefits, please complete and re t u rn the Wa rranty Registration Card enclosed in the shipping box within 15 days of purchase. Thank you. This Krell product has a limited warranty of five years for parts and labor on circuitry from date of purchase or six years from date of original shipment from the Krell factory.
R e t u rn Authorization Procedure HOW TO EXPEDITE SERVICE If you believe there is a problem with your component, please contact your dealer, distributor, or the Krell factory to discuss the problem before you return the component for repair. To expedite service, you may wish to complete and e-mail the Service Request Form in the Service section of our website at: http://www.krellonline.
Krell Industries, Inc. 45 Connair Road Orange, CT 06477-3650 USA S-300i Remote Control Integrated Amplifier TEL 203-799-9954, FAX 203-891-2028 E-MAIL krell@krellonline.com WEB SITE www.krellonline.com v 1.0 Specifications All operational features, functions, specifications, and policies are subject to change without notification. FREQUENCY RESPONSE OUTPUTS 20 Hz–20 kHz 2 loudspeaker via 5-standard +0 dB, -0.