5 6 royal series ice bins 095

Due to our commitment to continued product improvement, specications are subject to change without notice.
Rev. 3/2021 • 5.6
Krowne Metal Corporation • 100 Haul Rd. Wayne, NJ 07470 • P: [phone] • [e-mail] • krowne.com
Royal Series Ice Bins
Royal Series Underbar
Model:
Project:
Item #:
Qty:
Date:
Approved By:
 Available with 12” or 15” deep liners
 Available in 19” or 24” depths (front to back)
 Two bottle wells included
 Soda line access on cold plate units
 Optional built-in speed rail
 10 circuit cold plate available (All units with cold plates have soda
line cutout in rear)
Standard Features
Specifications
Optional Accessories
Material
 Interior: 20 gauge stainless steel
 Front Apron: 20 gauge stainless steel clad over
20 gauge galvanized steel
 Backsplash: 20 gauge stainless steel
 Back and Bottom: 20 gauge galvanized steel
Legs
 1-5/8” tubular 16 gauge stainless steel with grey
plastic bullet foot
Insulation
 Foamed-in-place polyurethane
Cold Plate
 Model numbers that end ‘-10’ include high
performance built-in 10-circuit post mix cold
plate. (KR19-18-7 and KR24-18-7 includes
7-circuit cold plate)
 Plate is sealed into bottom of ice bin
 Each circuit is 5/16” OD stainless steel tubing
 Two full with remainder to be half circuits
 Bump and swedge fittings on ends
Plumbing
 1” IPS drain connection
 Units with cold plates: 1/2” x 4” PVC tailpiece
(1/2” -20 male threaded) included.
 PVC tailpiece required to avoid condensation
through metal to metal contact
Tubing Access
(Cold Plate)
 3/4” x 3-1/2” cutout in left side of backsplash
KR19-24-10
Cold Plate Note
Health Departments require the optional built-in cold plates when using a soda
system. The cold plate is a large aluminum plate with stainless steel lines inside.
The soda system will be connected to the stainless steel lines which are chilled
from the ice inside the ice bin. The purpose of this plate is to chill the soda
before it is dispensed through the soda gun. A cold plate cannot be added to an
ice bin after it has been purchased.
Model Description
KR-101 Condiment Tray
KR-103 12” Deep Stainless Steel Divider for KR19
KR-109 12” Deep Stainless Steel Divider for KR24
KR-113 15” Deep Stainless Steel Divider for KR19
KR-114 15” Deep Stainless Steel Divider for KR24
KR-303 Left & Right End Side Splashes for KR19
KR-310 Right End Splash for KR19
KR-311 Left End Splash for KR19
KR-313 Left & Right End Side Splashes for KR24
KR-314 Right End Splash for KR24
KR-315 Left End Splash for KR24
KR-401 Cap Catcher and Opener
KR-406 Faucet Installed Over Ice Bin
KR-501 Towel Ring
KR-519 18” Garnish Station with Sliding Cover
KR-520 24” Garnish Station with Sliding Cover
KR-521 30” Garnish Station with Sliding Cover
KR-522 36” Garnish Station with Sliding Cover
SC”XX”H
Partial Sliding Cover for 19”D Ice Bin
(“XX” denotes length of Ice Bin, ex: SC24H)
SC”XX”F
Full Sliding Cover for 19”D Ice Bin
(“XX” denotes length of Ice Bin, ex: SC24F)
SCD”XX”H
Partial Sliding Cover for 24”D Ice Bin
(“XX” denotes length of Ice Bin, ex: SCD24H)
SCD”XX”F
Full Sliding Cover for 24”D Ice Bin
(“XX” denotes length of Ice Bin, ex: SCD24F)
RS-”XX”
Single Speed Rail
(“XX” denotes length of Ice Bin, ex: RS-24)
RD-”XX”
Double Speed Rail
(“XX” denotes length of Ice Bin, ex: RD-24)
30-550 3-Bottle Plastic Bottle Well for KR19 (qty 1)
30-502 3-Bottle Plastic Bottle Well for KR19 (qty 2)
KR-409 4-Bottle Plastic Bottle Well for KR24 (qty 1)
KR-410 4-Bottle Plastic Bottle Well for KR24 (qty 2)