SAFETY DATA SHEET 1501 Section 1. Identification Product name Product code Other means of identification : KRYLON® Interior/Exterior Paint Glossy White (OSHA White) : 1501 : Not available. Product type : Aerosol. Relevant identified uses of the substance or mixture and uses advised against Not applicable.
Section 2. Hazards identification Hazard statements : Extremely flammable aerosol. Contains gas under pressure; may explode if heated. Causes serious eye irritation. Causes skin irritation. Suspected of damaging the unborn child. Suspected of causing cancer. May be fatal if swallowed and enters airways. May cause respiratory irritation. May cause drowsiness and dizziness. May cause damage to organs through prolonged or repeated exposure.
Section 3. Composition/information on ingredients Ingredient name % by weight CAS number Acetone Methyl Ethyl Ketone Propane Xylene Butane Titanium Dioxide Ethylbenzene Toluene Methyl Isobutyl Ketone 36.1 13.8 13.6 7.3 6.4 6.4 1.3 0.2 0.
Section 4.
Section 5. Fire-fighting measures Special protective equipment for fire-fighters : Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Section 6. Accidental release measures Personal precautions, protective equipment and emergency procedures For non-emergency personnel : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas.
Section 7. Handling and storage Conditions for safe storage, including any incompatibilities : Store in accordance with local regulations. Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Protect from sunlight. Store locked up. Eliminate all ignition sources. Use appropriate containment to avoid environmental contamination. Section 8.
Section 8. Exposure controls/personal protection NIOSH REL (United States, 10/2013). TWA: 100 ppm 10 hours. TWA: 435 mg/m³ 10 hours. STEL: 125 ppm 15 minutes. STEL: 545 mg/m³ 15 minutes. OSHA PEL (United States, 2/2013). TWA: 100 ppm 8 hours. TWA: 435 mg/m³ 8 hours. OSHA PEL Z2 (United States, 2/2013). TWA: 200 ppm 8 hours. CEIL: 300 ppm AMP: 500 ppm 10 minutes. NIOSH REL (United States, 10/2013). TWA: 100 ppm 10 hours. TWA: 375 mg/m³ 10 hours. STEL: 150 ppm 15 minutes. STEL: 560 mg/m³ 15 minutes.
Section 8. Exposure controls/personal protection Hand protection Body protection Other skin protection Respiratory protection : Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties.
Section 10. Stability and reactivity Reactivity : No specific test data related to reactivity available for this product or its ingredients. Chemical stability : The product is stable. Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Conditions to avoid : Avoid all possible sources of ignition (spark or flame). Incompatible materials : No specific data.
Section 11.
Section 11. Toxicological information Name Category Route of exposure Target organs Acetone Category 3 Not applicable. Methyl Ethyl Ketone Category 3 Not applicable. Propane Category 3 Not applicable. Xylene Category 3 Not applicable. Butane Category 3 Not applicable. Ethylbenzene Category 3 Not applicable. Toluene Category 3 Not applicable. Methyl Isobutyl Ketone Category 3 Not applicable.
Symptoms related to the physical, chemical and toxicological characteristics Eye contact : Adverse symptoms may include the following: pain or irritation watering redness Inhalation : Adverse symptoms may include the following: respiratory tract irritation coughing nausea or vomiting headache drowsiness/fatigue dizziness/vertigo unconsciousness reduced fetal weight increase in fetal deaths skeletal malformations Skin contact : Adverse symptoms may include the following: irritation redness reduced fetal weig
Section 12. Ecological information Toxicity Product/ingredient name Result Species Exposure Acetone Acute EC50 20.565 mg/l Marine water Acute LC50 6000000 µg/l Fresh water Acute LC50 10000 µg/l Fresh water Acute LC50 5600 ppm Fresh water Chronic NOEC 4.95 mg/l Marine water Chronic NOEC 0.016 ml/L Fresh water Chronic NOEC 0.
Section 12. Ecological information Product/ingredient name LogPow BCF Potential Xylene Titanium Dioxide Toluene - 8.1 to 25.9 352 90 low low low Mobility in soil Soil/water partition coefficient (KOC) : Not available. Other adverse effects : No known significant effects or critical hazards. Section 13. Disposal considerations Disposal methods : The generation of waste should be avoided or minimized wherever possible.
Section 14. Transport information and on all actions in case of emergency situations. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code : Not available. Section 15. Regulatory information U.S. Federal regulations State regulations : California Prop. 65 WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Section 16. Other information Hazardous Material Information System (U.S.A.
Section 16. Other information instructions. Due to the proliferation of sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs obtained from any other source. Date of issue/Date of revision : 6/2/2015. Date of previous issue : 4/8/2015. Version : 1.
