M162-HDN300-001 HD CCTV Digital Video Camera O PE R AT ION MANUAL Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. EQUIPMENT AND ACCESSORIES 4. INSTALLATION 5. DIMENSIONS 6. SPECIFICATION 7. OSD MANUAL CA UTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3. EQUIPMENT AND ACCESSORIES S tan d a rd T ype Cable Concealed Type Cam e r a Sun shield Tapping Screw Ø4x20 (3ea) Tapping Screw Ø4x16 (3ea) Screw / L-Wrench / Washer / Coin Hole Bolt Coin Hole Bolt Coin Hole Bolt Washer L-Wrench Washer Manual C A UTION • Service Video Output looks the angle of view narrower than HD-SDI Output.
4. INSTALLATION • CAMERA MOUNTING POSITION Please assemble a coin hole bolt as shown above. Cable Concealed Thru Bracket(Option) When using the cable concealed bracket, it is not able to install on the ceiling.
4. INSTALLATION • MONITOR CONNECTION * Option: Remote Control (OSD Key) RCA Jack (OSD Key Jack / White) BNC Female (2'nd Video / Yellow) DC12V Adapter DC12V IN (Black) BNC Female (HD-SDI Jack) HD-SDI IN Monitor When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems. * Remote Control - Circuit Diagram (Option) SW1 Menu SW2 Up SW3 Down Function SW1: Menu OSD Menu on / off, Selection. SW2: Up OSD Menu up.
5.
6. SPECIFICATION Image Device Effective Pixels Unit cell size Video output mode Minimum Illumination Shutter speed Day/Night White Balance 1/3” 2.1 Mega Pixel SONY CMOS 1984(H) x 1105(V) 2.8um (H) x 2.8um (V) SDI: 1080P 30fps(25fps) / 720P 60fps(50fps) TV Out: CVBS NTSC/PAL 0 Lux (IR-LED ON) Auto / Manual selectable 1/30(25),1/60(50),1/120(100),1/250,1/ 700, 1/1K,1/1.6K,1/2.
7. OSD MANUAL 1. EXPOSURE - BRIGHTNESS: Enable user to control the image brightness (1~20steps). - SHUTTER MODE: Enable user to set up the Shutter Mode. -> AUTO, MANUAL EXPOSURE > BRIGHRNESS SHUTTER MODE SHUTTER SPEED DSS AGC MAX INITIAL RETURN ||||||||||||10 AUTO ––– X2 18dB - SHUTTER SPEED: Enable user to set up the Shutter Speed. -> 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K, 1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K. *() is for power-frequency 50Hz.
7. OSD MANUAL 3. BLC - MODE: BLC Enable user to set BLC mode. > MODE -> OFF, BLC BLC ZONE BLC X - POSITION - BLC(Backlight compensation mode): BLC Y - POSITION This function works for subjects in the BLC X - SIZE kind of backlight conditions. BLC Y - SIZE INITIAL - BLC ZONE: RETURN Enable user to set up screen output of chosen BLC zone. - BLC X-POSITION: Enable user to set up screen output of chosen BLC zone. - BLC Y-POSITION: Enable user to set up Horizontal start position (0~20steps).
7. OSD MANUAL 5. IMAGE - SHARPNESS: Enable user to control the image sharpness(0~10steps). - FLIP: Sets the Vertical flip for the display output. IMAGE (OFF) (V-FLIP) > SHARPNESS FLIP DZOOM HLMASK D-WDR DNR INITIAL RETURN (H-FLIP) ||||||||||||8 OFF 1.0X OFF OFF MIDDLE (HV-FLIP) - DZOOM(Digital Zoom): Max. 20x Digital Zoom. - HLMASK: This function that improves the visual recognition of license plates and other such objects by suppressing or masking strong light sources. 1.
7. OSD MANUAL 6. SPECIAL : Setting up the CAM TITLE, LANGUAGE, PRIVACY, DISPLAY, SYSTEM. SPECIAL - CAM TITLE : Enable user to choose any word in screen. (Maximum 10 letter is available) 1. A letter Choice from the screen using Menu key. 2. Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION. 3. By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in LOCATION and then get back to previous step. 4.
7. OSD MANUAL - MOTION: Motion detection function. 1. RESOLUTION: Enable user to set up resolution 2. SENSITIVITY: Enable user to set up sensitivity. 3. WINDOW USE: Enable user to select to motion area. 4. WINDOW TONE: Enable user to area window tone. 5. X-POSITION : Window Horizontal start position. 6. Y-POSITION : Window Vertical start position. 7. X-SIZE : Window Horizontal width. 8. Y-SIZE : Window Vertical height. 9. INITIAL : Enable user to initialize setting of MOTION DETECT.
