M177-HLD(N)D45-001 HD CCTV Digital Video Camera O PERATI O N M ANUAL Thank you for choosing our high quality camera. Before attempting to connect or operate this unit, please read and follow these instructions.
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTIONS 3. EQUIPMENT AND ACCESSORIES 4. CAMERA COMPONENT DESCRIPTIONS 5. INSTALLATION 6. DIMENSIONS 7. SPECIFICATIONS 8. OSD MANUAL • Menu Structure • Function Description CAUTIO N These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. CAUTIONS WEEE (Waste Electrical & Electronic Equipment) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3.
4.
5. INSTALLATION 1. Attach the Camera to the ceiling with using the screws provided, taking into considering the camera angle required for the surveillance function. Template M4 Tappint Screw - 3EA 2. Adjust the LENS ANGLE to the desired location by hand.
5. INSTALLATION 3. Connect the VIDEO OUT CABLE and check the video image. Change the SETTINGS accordingly using the OSD controller. Controller Test Video Connector Video Output Test Cable 4. After the SETTING is completed, install the TOP COVER.
5. INSTALLATION • MONITOR CONNECTION DC12V/AC24V POWER SUPPLY - DC12V/AC24V + - DC12V/AC24V (TERMINAL BLOCK) MONITOR BNC FEMALE VIDEO IN CAMERA - DC12V DC12V ADAPTER DC12V (DC JACK) MONITOR BNC FEMALE VIDEO IN CAMERA When you install the camera, please glue the end of cable to keep it stable in order to protect the camera from humidity problems.
55 6.
7. SPECIFICATIONS LED Type Image Sensor Standard Type 1/3” 2.1 Mega Pixel SONY CMOS Effective Pixels 1984(H) x 1105(V) Unit cell size 2.8um (H) x 2.8um (V) Video output mode SDI: 1080P 30fps(25fps) / 720P 60fps(50fps) TV Out: CVBS NTSC/PAL Minimum Illumination 0 Lux 0.1 Lux Auto / Manual 1/30(25),1/60(50),1/120(100),1/250,1/ 700, 1/1K,1/1.6K,1/2.
8. OSD MANUAL 1. EXPOSURE - BRIGHTNESS: Enables user to control the image brightness (1~20steps). EXPOSURE - SHUTTER MODE: Enables user to set the Shutter Mode. -> AUTO, MANUAL, FLICKER - SHUTTER SPEED: Enables user to set the Shutter Speed. -> 1/30(25), 1/60(50), 1/120(100), 1/250, 1/700, 1/1K, 1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K.
8. OSD MANUAL 3. WDR/BLC - MODE: Enables user to set WDR/BLC mode. -> OFF, WDR, BLC WDR / BLC ① WDR(Wide Dynamic Range): For use in conditions were BLC is not sufficient to produce a clean image, such as in lobbies and places surrounded by windows. ② BLC(Backlight Compensation): This function helps make subjects visible in backlit conditions. > MODE WDR LEVEL BLC ZONE BLC X - POSITION BLC Y - POSITION BLC X - SIZE BLC Y - SIZE INITIAL RETURN - WDR LEVEL: Enables user to set WDR Level (0~4 level).
8. OSD MANUAL 4-2. DAY&NIGHT (Standard Type) Conversion of output image to COLOR / BW depending on exterior environment. - D&N MODE 1. COLOR: Enables user to set the image to color mode. 2. B/W: Enables user to set the image to B/W mode. 3 AUTO: Enables user to convert to COLOR/BW automatically by photocell - DWELL TIME: In D&N MODE AUTO, enables user to set a delay when for changing COLOR/BW(0~10sec). - AGC THRS: The threshold AGC value for switching from Day to Night.
8. OSD MANUAL 6. SPECIAL : For setting up the CAM TITLE, LANGUAGE, MOTION PRIVACY, DISPLAY, SYSTEM. SPECIAL > CAM TITLE LANGUAGE PRIVACY MOTION DISPLAY SYSTEM INITIAL RETURN [ ] ENGLISH OFF OFF [ ] [ ] - CAM TITLE : Enables user to choose any name for the camera. (10 letter maximum) 1. Choose a letter on the screen using the Menu Key 2. Move to the next menu by using the LEFT, RIGHT KEY in LOCATION. 3.
8. OSD MANUAL - MOTION: Motion detection function. 1. RESOLUTION: Enables user to set resolution 2. SENSITIVITY: Enables user to set sensitivity. 3. WINDOW USE: Enables user to turn motion detection ON/OFF for the selected window. 4. WINDOW TONE: Enables user to choose how to display the motion detection window. 5. X-POSITION : Window Horizontal start position. 6. Y-POSITION : Window Vertical start position. 7. X-SIZE : Window Horizontal width. 8. Y-SIZE : Window Vertical height. 9.
