M151-HNV522-001 HD CCTV Digital Video IR LED Dome Camera U s e r Man u al Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CAUTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. FEATURES 4. EQUIPMENT AND ACCESSORIES 5. CAMERA COMPONENT DESCRIPTIONS 6. INSTALLATION 7. DIMENSIONS 8. SPECIFICATION 9.
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3. FEATURES • High Resolution SONY 1 / 3” 2.
4. EQUIPMENT AND ACCESSORIES Camera Manual Template Screws, Set Screw / L-Wrench / Plastic Anchors Plastic Anchors Screws L-Wrench Option - Remote Control (OSD Key) Max.
5.
6. INSTALLATION Template 70° 140° 70° Plastic Anchors (4ea) Tapping Screws-4x25L (4ea) Open Set Screw-M2.
6. INSTALLATION • MONITOR CONNECTION * Option: Remote Control (OSD Key) RCA Jack (OSD Key Jack) BNC Female (2'nd Video) DC12V Adapter DC12V IN (Black) BNC Female (HD-SDI Jack) HD-SDI IN Monitor * Remote Control - Circuit Diagram (Option) Function SW1: Menu OSD Menu on / off, Selection. SW2: Up OSD Menu up. SW3: Down OSD Menu Down. SW4: Left OSD Menu Left. SW5: Right OSD Menu Right.
7. DIMENSIONS Unit(mm) Ø 93 77 (The maximum rotation) 63 Ø 69 20-IR LED 4-Ø4.5 Ø68 .
8. SPECIFICATION Image Device Effective Pixels Unit Cell Size(um) Video Output Mode Minimum Illumination Video Output IR LED IR Beam Range S/N Ratio Shutter Speed Manual Shutter Speed D-WDR / BLC AGC 3DNR Day & Night White Balance Digital Zoom Ratio Privacy Masking Lens OSD Power Consumption Weight Dimension(mm) Conformity Temperature / Humidity (no condensing) 2.1Mega Pixel. 3/1" Exmor SONY CMOS 1984 (H) x 1105 (V) 30fps 2.8 (H) x 2.
9. OSD MANUAL • Menu structure Main Sub Menu BRIGHTNESS SHUTTER EXPOSURE DSS AGC BASE FREQ RESET DATA RETURN WB MODE WHITE BALANCE D-WDR / BLC DNR SATURATION RESET DATE RETURN MODE BLC OSD BLC POS-X BLC POS-Y BLC SIZE-X BLC SIZE-Y RESET DATA RETURN Sub Menu 0 ~ 20 1/30(25), 1/60(50), 1/120(100), 1/240, 1/500, MANUAL / LEVEL 1/1K, 1/2K, 1/4K, 1/8K, 1/16K, 1/30K, 1/60K. AUTO RETURN BACK / EXIT OFF, X2, X3, X4, X5, X6, X7, X8 0 ~ 10 60Hz / 50Hz BACK / DEF. BACK / EXIT. COLORTEMP.
9. OSD MANUAL Main IMAGE Sub Menu SHARPNESS GAMMA FLIP LENS SHADING DZOOM RESET DATA RETURN PRIVACY SPECIAL HLMASK PATTERN RESET DATA RETURN SDI FORMAT SDI FPS CVBS FORMAT SYSTEM APPLY SYSTEM INFO.
9. OSD MANUAL • Function Description 0. SETUP - EXPOSURE - WHITE ALANCE - D-WDR / BLC - DNR - IMAGE - SPECIAL - SYSTEM - Reset Data All : Go sub menu for camera exposure control. : Go sub menu for camera white balance control. : Go sub menu for camera D-WDR or BLC action. : Control noise reduction setting. : Go sub menu for adjust image functions. : Go sub menu for special feature control. : Go sub menu for system control & information. : Reset camera’s all feature data to default value. 1.
9. OSD MANUAL 3. D-WDR / BLC - MODE > BLC > D-WDR - BLC OSD - BLC POS-X - BLC POS-Y - BLC SIZ-X - BLC SIZ-Y : Select D-WDR / BLC mode. : Act in Backlight compensation mode. : Digital wide dynamic range control. : Display BLC control zone in screen. : Select BLC control zone vertical position. : Select BLC control zone horizontal position. : Select BLC control zone vertical size. : Select BLC control zone horizontal size. 4. DNR: Reduce image’s noise 5.
9. OSD MANUAL 7. SYSTEM - SDI FORMAT - SDI FPS - CVBS FORMAT • CVBS VIEW ◦ CROP ◦ FULL - APPLY - SYSTEM INFO. • S/W VERSION • SET VERSION : 1080P / 720P : 30 or 25 fps in 1080p mode. 60 or 50 fps in 720p mode. : NTSC / PAL : CVBS out video angle setting. : Cut the scene outside area for keep image aspect ratio. : Fill the full angle scene into image with H-V size & ratio change. : Apply all video setting changed at once. Use the Set button to apply. : Camera’s basic software version.
