M150-LD40LV40-001 HIGH PERFORMANCE WDR FLAT DOME CAMERA O PERATI O N M ANUAL VANDAL DOME PLASTIC DOME Thank you for choosing our high quality camera. Before attempting to connect operate this unit, please read and follow these instructions.
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. EQUIPMENT AND ACCESSORIES 4. CAMERA COMPONENT DESCRIPTIONS • Plastic Dome / Vandal Dome Type 5. INSTALLATION • Plastic Dome / Vandal Dome Type 6. DIMENSIONS • Plastic Dome / Vandal Dome Type 7. SPECIFICATION 8. OSD MANUAL • Menu structure • Function Description CAUTIO N These servicing instructions are for use by qualified service personnel only.
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
3.
4.
4.
5. INSTALLATION (Plastic Dome) 1. Attach the FLAT DOME on the ceiling with using the screws provided, considering the camera angle required for the surveillance function. 2. Adjust the LENS ANGLE to the desired location by hand. TAPPING SCREW (4 x 20L) - 3EA 3. Connect the VIDEO OUT CABLE and check the video image. Change the SETTINGS accordingly using the OSD controller.
5. INSTALLATION (Vandal Dome) 1. Attach the FLAT DOME on the ceiling with using the screws provided, considering the camera angle required for the surveillance function. 2. Adjust the LENS ANGLE to the desired ocation by hand. 3. Please remove the protective film when installing. TAPPING SCREW (4 x 20L)-3EA 4. Connect the VIDEO OUT CABLE and check the video image. Change the SETTINGS accordingly using the OSD controller.
5. INSTALLATION • MONITOR CONNECTION - DC12V/AC24V DC12V/AC24V (TERMINAL BLOCK) DC12V/AC24V POWER SUPPLY MONITOR BNC FEMALE VIDEO IN CAMERA - DC12V DC12V ADAPTER DC12V (DC JACK) MONITOR BNC FEMALE VIDEO IN CAMERA When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
6.
7. SPECIFICATION NTSC Image Sensor PAL 1/3” 960H SONY Double Scan Super HAD CCD II Scanning System 2 : 1 Interlace H Resolution. 750TV Lines Scanning Frequency 15.734KHz(H), 59.94Hz(V) 1 5 . 625KHz( H ) , 5 0 H z ( V ) Total Pixels No. 1028(H) X 508(V) 1028(H) X 596(V) Effective Pixels No. 976(H) X 494(V) 976(H) X 582(V) More than 50dB(AGC OFF, 3DNR ON) S/N Ratio Min. Illumination Color:0.1Lux, BW:0.1Lux (30IRE@F2.0, AGC 36dB) 0.000001Lux (DSS x256) Sync System Internal Gamma r= 0.
8. OSD MANUAL • Menu structure Main MENU 1st Sub MENU 2nd Sub MENU HIGH LUMINANCE AUTO EXPOSURE LOW LUMINANCE 3rd Sub MENU 4th Sub MENU FLICKERLESS OFF / ON BRIGHTNESS 0 ~ 255 MODE AGC, SLOW, AGC > SLOW, SLOW > AGC, OFF AGC MAX 6, 12, 18, 24, 30, 36 DSS MAX 2, 4, 8, 16, 32, 64, 128, 256 BRIGHTNESS x0.25, x0.5, x0.75, x1.
8.
