Manual

ManualsBrandsKT&C ManualsCamcordersKPC-N701NU8

HIGH PERFORMANCE

Super Night Vision Camera

OPERATION MANUAL

Thank you for choosing our high quality camera. Before attempting

to connect operate this unit,please read and follow these instructions.

M117-N701-001

Summary of content (49 pages)

PAGE 1
M 117- N 701- 001 HIGH PERFORMANCE Super Night Vision Camera O PE R AT ION MANUAL T h a n k y o u f o r cho o si ng o u r hi gh q uality cam er a. Befor e attem pting to co n n e c t o p e r ate th i s un i t,pl ea se r ead and follow these instr uctions.
PAGE 2
M 117- N 701- 001 HIGH PERFORMANCE Super Night Vision Camera O PE R AT ION MANUAL T h a n k y o u f o r cho o si ng o u r hi gh q uality cam er a. Befor e attem pting to co n n e c t o p e r ate th i s un i t,pl ea se r ead and follow these instr uctions.
PAGE 3
CA UTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
PAGE 4
CONTENTS 1 . CA UT IONS 2 . I MP OR TANT SAFETY INSTRUCTI O NS 3 . F E A T URES 4 . COMP ONENTS 5 . NA ME AND FUNCTION 6 . I NS T A LLATION 7 . DIME NSIONS 8 . S P E C I FICATION 9 . O S D MANUAL 1 0 .
PAGE 5
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 6
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
PAGE 7
2 . IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
PAGE 8
3. FEATURES • 1/3 960H SONY EXview HAD CCD II • High Resolution of 700TV Lines • OSD Function • Multi Language (ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE) • 2DNR • Privacy Zone / Motion Detect • Smart IR • DC12V / AC24V Dual Voltage • ATR(Adaptive Tone-curve Reproduction / Digital WDR) The function provides gradation compensation to improve the contrast of subjects both low-luminance areas and high luminance areas exist in the same picture 4.
PAGE 9
5.
PAGE 10
5. NAME AND FUNCTION • Heater Heater Built in heater protects the camera from low temperature.
PAGE 11
6.
PAGE 12
6. INSTALLATION • MONITOR CONNECTION DC 12V POWER SUPPLY or AC 24V POWER SUPPLY DC12V/AC24V VIDEO IN MONITOR DC 12V POWER SUPPLY or AC 24V POWER SUPPLY DC12V/AC24V BNC FEMALE VIDEO IN MONITOR RS485 When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
PAGE 13
7. DIMENSIONS 83 Ø80.6 Unit : mm 45 LED SENSOR 140 110.6 243.3 10 M12XP1.25 Ø95 12 135 125 106.
PAGE 14
8. SPECIFICATION Signal Format Image Device NTSC PAL 1/3˝ 960H SONY EXview HAD CCD II Scanning System Scanning Frequency 2 : 1 Interlace 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V) Total Pixels 1020(H) X 508(V) 1020(H) X 596(V) Effective Pixels 976(H) X 494(V) 976(H) X 582(V) Electronic Shutter Speed 1/60 sec H.Resolution 1/50 sec 750TV Lines S/N Ratio More than 50dB(AGC OFF) Min.Illumination LED On : 0 Lux Sync System Internal Gamma r= 0.45 Video Output Level 1.
PAGE 15
9. OSD MANUAL GENERAL STRUCTURE SETUP >FOCUS ADJUST EXPOSURE WHITE BALANCE BLC DAY&NIGHT IMAGE SPECIAL FACTORY DEFAULT EXIT FOCUS ADJUST [-] [-] [-] [-] [-] [-] [-] > RETURN EXPOSURE ... 7 ... 1/60 ... OFF ...
PAGE 16
9.
PAGE 17
9.
PAGE 18
9.
PAGE 19
9. OSD MANUAL OSD FUNCTION DESCRIPTION 1. FOCUS ADJUST : According to the brightness of light to minimize the depth of focus, to be more accurate to focus. FOCUS >RETURN 2. EXPOSURE : Enable user to set up the function of BRIGHTNESS, SHUTTER, FLICKERLESS, AGC. Set up using LEFT, RIGHT KEY at each menu. EXPOSURE >BRIGHTNESS SHUTTER FLICKERLESS AGC MAX INTIAL RETURN 7 1/60 OFF 30dB - BRIGHTNESS : Enable user to control the image brightness (0~15steps).
PAGE 20
9. OSD MANUAL 3. WHITE BALANCE : Enable user to represent the accurate white color by controlling the R,G,B level. Setting up LEFT, RIGHT KEY on each menu. - WB MODE ① ATW : Enable user to trace the White Balance automatically in the range of 2,300K~10,000K. ② PUSH : Enable user to search for White Balance automatically. In this mode, color temperature range is broader than ATW. ③ PUSH LOCK : Enable user to fix the White Balance according to the color temperature in the certain environment.
PAGE 21
9. OSD MANUAL - BLC ZONE : Enable user to set the BLC area TOP -> TOP, BOTTOM, CENTER, LEFT, RIGHT. - BLC LEVEL : Enable user to set BLC in selected area(0~15 level). LEFT - INITIAL : Enable user to initialize the BLC setting. CENTER RIGHT BOTTOM 5. DAY&NIGHT : Conversion of output image COLOR / BW depending on exterior environment Enable user to set the LEFT, RIGHT KEY in menu. - D&N MODE ① COLOR : Enable user to fit the output image in color. ② B/W : Enable user to fit the output image in B/W.
PAGE 22
9. OSD MANUAL 6. IMAGE : MIRROR, DNR, SHARPNESS functions set up by pressing LEFT, RIGHT KEY. IMAGE >MIRROR DNR DNR LEVEL SHARPNESS INITAL RETURN OFF ON 4 8 (OFF) (ON) - MIRROR: Enable user to reverse the image. - DNR : This function reduces noise by undertaking spatial filtering for one image. (Outline of DNR function) - DNR LEVEL : Enable user to set level(0~15 steps). - SHARPNESS : Enable user to control the image sharpness (0~15steps).
PAGE 23
9. OSD MANUAL - CAM TITLE : Enable user to choose any word in screen(Maximum 10 letter is available) ① A letter Choice from the screen using menu key ② Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION. ③ By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in LOCATION and then get back to previous step.
PAGE 24
9. OSD MANUAL - MOTION DETECT : Motion detection function. ① MOTION MODE : Enable user to set up ON/OFF ② LEVEL : Enable user to setup a motion detect sensitivity (0~3) ③ V START : Motion area Vertical start position. ④ V END : Motion area Vertical end position. MOTION DETECT ⑤ H START : Motion area Horizontal start position. ⑥ H END : Motion area Horizontal end position.
PAGE 25
10.
PAGE 26
PAGE 27
CA UTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
PAGE 28
CONTENTS 1 . CA UT IONS 2 . I MP OR TANT SAFETY INSTRUCTI O NS 3 . F E A T URES 4 . COMP ONENTS 5 . NA ME AND FUNCTION 6 . I NS T A LLATION 7 . DIME NSIONS 8 . S P E C I FICATION 9 . O S D MANUAL 1 0 .
PAGE 29
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 30
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
PAGE 31
2 . IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
PAGE 32
3. FEATURES • 1/3 960H SONY EXview HAD CCD II • High Resolution of 700TV Lines • OSD Function • Multi Language (ENGLISH, CHINESE, RUSSIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE, JAPANESE) • 2DNR • Privacy Zone / Motion Detect • Smart IR • DC12V / AC24V Dual Voltage • ATR(Adaptive Tone-curve Reproduction / Digital WDR) The function provides gradation compensation to improve the contrast of subjects both low-luminance areas and high luminance areas exist in the same picture 4.
PAGE 33
5.
PAGE 34
5. NAME AND FUNCTION • Heater Heater Built in heater protects the camera from low temperature.
PAGE 35
6.
PAGE 36
6. INSTALLATION • MONITOR CONNECTION DC 12V POWER SUPPLY or AC 24V POWER SUPPLY DC12V/AC24V VIDEO IN MONITOR DC 12V POWER SUPPLY or AC 24V POWER SUPPLY DC12V/AC24V BNC FEMALE VIDEO IN MONITOR RS485 When you install the camera, please glue up the end of cable to keep it stable in order to protect the camera from the humidity problems.
PAGE 37
7. DIMENSIONS 83 Ø80.6 Unit : mm 45 LED SENSOR 140 110.6 243.3 10 M12XP1.25 Ø95 12 135 125 106.
PAGE 38
8. SPECIFICATION Signal Format Image Device NTSC PAL 1/3˝ 960H SONY EXview HAD CCD II Scanning System Scanning Frequency 2 : 1 Interlace 15.734KHz(H), 59.94Hz(V) 15.625KHz(H), 50Hz(V) Total Pixels 1020(H) X 508(V) 1020(H) X 596(V) Effective Pixels 976(H) X 494(V) 976(H) X 582(V) Electronic Shutter Speed 1/60 sec H.Resolution 1/50 sec 750TV Lines S/N Ratio More than 50dB(AGC OFF) Min.Illumination LED On : 0 Lux Sync System Internal Gamma r= 0.45 Video Output Level 1.
PAGE 39
9. OSD MANUAL GENERAL STRUCTURE SETUP >FOCUS ADJUST EXPOSURE WHITE BALANCE BLC DAY&NIGHT IMAGE SPECIAL FACTORY DEFAULT EXIT FOCUS ADJUST [-] [-] [-] [-] [-] [-] [-] > RETURN EXPOSURE ... 7 ... 1/60 ... OFF ...
PAGE 40
9.
PAGE 41
9.
PAGE 42
9.
PAGE 43
9. OSD MANUAL OSD FUNCTION DESCRIPTION 1. FOCUS ADJUST : According to the brightness of light to minimize the depth of focus, to be more accurate to focus. FOCUS >RETURN 2. EXPOSURE : Enable user to set up the function of BRIGHTNESS, SHUTTER, FLICKERLESS, AGC. Set up using LEFT, RIGHT KEY at each menu. EXPOSURE >BRIGHTNESS SHUTTER FLICKERLESS AGC MAX INTIAL RETURN 7 1/60 OFF 30dB - BRIGHTNESS : Enable user to control the image brightness (0~15steps).
PAGE 44
9. OSD MANUAL 3. WHITE BALANCE : Enable user to represent the accurate white color by controlling the R,G,B level. Setting up LEFT, RIGHT KEY on each menu. - WB MODE ① ATW : Enable user to trace the White Balance automatically in the range of 2,300K~10,000K. ② PUSH : Enable user to search for White Balance automatically. In this mode, color temperature range is broader than ATW. ③ PUSH LOCK : Enable user to fix the White Balance according to the color temperature in the certain environment.
PAGE 45
9. OSD MANUAL - BLC ZONE : Enable user to set the BLC area TOP -> TOP, BOTTOM, CENTER, LEFT, RIGHT. - BLC LEVEL : Enable user to set BLC in selected area(0~15 level). LEFT - INITIAL : Enable user to initialize the BLC setting. CENTER RIGHT BOTTOM 5. DAY&NIGHT : Conversion of output image COLOR / BW depending on exterior environment Enable user to set the LEFT, RIGHT KEY in menu. - D&N MODE ① COLOR : Enable user to fit the output image in color. ② B/W : Enable user to fit the output image in B/W.
PAGE 46
9. OSD MANUAL 6. IMAGE : MIRROR, DNR, SHARPNESS functions set up by pressing LEFT, RIGHT KEY. IMAGE >MIRROR DNR DNR LEVEL SHARPNESS INITAL RETURN OFF ON 4 8 (OFF) (ON) - MIRROR: Enable user to reverse the image. - DNR : This function reduces noise by undertaking spatial filtering for one image. (Outline of DNR function) - DNR LEVEL : Enable user to set level(0~15 steps). - SHARPNESS : Enable user to control the image sharpness (0~15steps).
PAGE 47
9. OSD MANUAL - CAM TITLE : Enable user to choose any word in screen(Maximum 10 letter is available) ① A letter Choice from the screen using menu key ② Enable user to move to next menu using LEFT, RIGHT KEY in LOCATION. ③ By using UP, DOWN, LEFT, RIGHT KEY, enable user to choose any letters in LOCATION and then get back to previous step.
PAGE 48
9. OSD MANUAL - MOTION DETECT : Motion detection function. ① MOTION MODE : Enable user to set up ON/OFF ② LEVEL : Enable user to setup a motion detect sensitivity (0~3) ③ V START : Motion area Vertical start position. ④ V END : Motion area Vertical end position. MOTION DETECT ⑤ H START : Motion area Horizontal start position. ⑥ H END : Motion area Horizontal end position.
PAGE 49
10.