M056-ZA180-002 1/3 Inch CCD D a y & N i g h t 180x COLOR ZOOM C A M E R A O P E R AT I ON MANUAL About this manual Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
z CONTENTS 1. 2. 3. 4. C a u t i on s Precautions Features C o m p o n e n t s a n d A c c e ssories • Package • T r i p o d Mounting 5 . O v e r v ie w • R e a r V i ew 6. Installation • C o n n e c ting to Monitor • C o n n e c ting to Power • C o n n e c ting to Connection 7. Operating Camera • O n S c r een Display(OSD) • O S D M enu Configuration • M e n u S etup - L ENS - E XPOSURE - W HITE BALANCE - B LC - D AY & NIGHT - I MAGE - S PECIAL - T ITLE - P RIVACY - D ISPLAY - M OTION DETECT 8 .
1 .Cau tions INFORMATION This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
1 .Cau tions Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
CAUTIONS 2 .Precautions 1 Do not operate under extreme temperature conditions. Using the camera in temperatures exceeding 50˚C or below -10˚C may lower image quality or cause the camera to malfunction. Do not operate in high humidity environments. Using the camera in places with high humidity may lessen picture quality because of moisture on the lens. Do not operate under unsteady lighting.
3 .Features 1/3 Inch Super HAD CCD High resolution SONY 1/3 Inch Super HAD CCD II with 380,000(NTSC) or 440,000(PAL) effective pixels, delivers an excellent signal-to-noise ratio, exceptional low-light performance, enhanced FOV, and high image quality. The minimum illumination required is 0.1 Lux(Day Mode, ICR OFF) 18x Optical Zoom The Built-in 18x Optical zoom lens is a highly durable component. It features Auto Focus, Auto Iris and Zoom functions.
FEATURES CAUTIONS 412.Components and Accessories Package Operation Manual Operation Manual Mounting Tripod & Screw Tripod Mounting Hole Used to install the camera on an optional tripod. The tripod must be equipped with screws with specifications shown on the right. Tripod Mounting Attach the tripod to the camera. Use screws included in the package or their equivalent (less than 6mm). Otherwise, the bracket may not assemble to the camera properly.
5 .Overview Rear View Video Out Jack Key Butt o n s Power LED Control Interface Power Input Terminal Key Buttons • Following buttons control zoom, focus, and auto focus functions. W(WIDE) button : To widen the view. (ZOOM OUT) T(TELE) button : To close in on a far object. (ZOOM IN) N(NEAR) button : To see a near object clearly. F(FAR) button : To see a far object clearly. • Pressing the M(MENU) button prompts the main setup menu. • Setup menu can be navigated using these buttons.
5 .Overview Control Interface • Used to connect the remote control equipment. Includes the RS-485 communication pin. Zoom and focus functions can be controlled by using external signals. Power LED • Illuminates when power is supplied. Video Output Jack • Used to connect an external video monitor in jack.
6 .Installation Connecting to Monitor • Connect Video Out Jack to the monitor's Video In Jack as shown below. • Connection methods may vary depending on the video equipment. Please refer to the model specific instruction manual. • Connect cables with the unit powered down. Set the 75Ω / Hi - Z selection switch as shown below if you have an intermediate device.
6 .Installation Connecting to Power Connect the power cable to the camera's power in as shown in the figure below Resistance of copper wire [at 20℃ (68˚F)] Copper wire size (AWG) #24 (0.22㎟) #22 (0.33㎟) #20 (0.52㎟) #18 (0.83㎟) Resistance(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop(V/m) 0.028 0.018 0.011 0.006 • As the voltage drop according to the length of the cable in the above table, a camera may malfunction if there is an excessively long cable run.
6 .Installation Control Interfaces(Communication Control Connector) The camera can be controlled by using external controllers like as the keyboard controller.
6 .Installation Connecting to External Controller Controller Function Table FUNC.
6 .Installation External D&N Input / Output • It can be switched to DAY mode or NIGHT mode by receiving the signal from external light sensor or IR LED LAMP. when D&N Mode is set " EXTERNAL" on the OSD menu of the Camera. J705 High(+5V) : NIGHT LOW(GND) : DAY ① Day/Night EXT ② GND • It can be sent signal to other equipment like as IR LED lamp. In this case, IR LED lamp can turn on using this signal. J706 High(+3.
7 .Operating Ca m e r a OSD Menu Configuration SETUP 1.LENS 2.EXPOSURE 3.WHITE BALANCE 4.BLC 5.DAY&NIGHT 6.IMAGE 7.SPECIAL 8.FACTORY DEFAULT 9.EXIT [┛] [┛] [┛] [┛] [┛] [┛] [┛] LENS FOCUS MODE FOCUS LIMIT ZOOM START ZOOM STOP ZOOM SPEED E-ZOOM INITIAL RETURN ... AUTO ... 50CM ... x1 ... x180 ... 15 ... ON EXPOSURE AE MODE BRIGHTNESS FLICKERLESS SHUTTER AGC LEVEL MAX AGC GAIN MAX FIELDS INITIAL RETURN ... SHUT FIX ... 8 ... OFF ... 1/60 ... AUTO ... 29dB ...
7 .Operating Ca m e r a BLC ... OFF ... CENTER ... 04 BLC MODE BLC ZONE BLC LEVEL INITIAL RETURN DAY & NIGHT TITLE [TITLE LOCATION] [M] [┛] ↓ ... AUTO ... SENSOR ... 5 SEC ... 8 LUX ... 100 LUX ... OFF D&N MODE DETECT MODE DWELL TIME D->N LEVEL N->D LEVEL BURST(NIGHT) INITIAL RETURN __________ [M]select ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 0123456789ÄÖÜÈÆäöüáéíñóúßæ MORE>> SPACE>> <
7 .
7 .
7 .Operating Ca m e r a Menu Setup Use the five buttons on back of the camera. F u n c t i on S e t u p Key NEAR(LEF T ) B U T T O N TELE(UP) BUTTON FAR(RIGHT) BUTTON MENU BU T T O N WIDE(DOW N ) B U T T O N 1. Press the MENU button to access the main setup mode. • Main setup menu is displayed on the monitor screen. • The Menu consists of the "Main-Menu" and "Sub-Menu" NEAR/FAR TELE/WIDE SETUP 1.LENS 2.EXPOSURE 3.WHITE BALANCE 4.BLC 5.DAY&NIGH 6.IMAGE 7.SPECIAL 8.FACTORY DEFAULT 9.
7 .Operating Ca m e r a Menu Setup 3. Select the desired feature using the TELE and WIDE button. • The indicator moves up and down in the main menu feature. • Move the arrow indicator to the desired feature. SETUP 1.LENS 2.EXPOSURE 3.WHITE BALANCE 4.BLC 5.DAY&NIGH 6.IMAGE 7.SPECIAL 8.FACTORY DEFAULT 9.EXIT [┛] [┛] [┛] [┛] [┛] [┛] [┛] 4. Change the status of the selected feature using the NEAR and FAR button • Pressing the NEAR/FAR button, the sub-menu is displayed.
7 .Operating Ca m e r a Sub-Menu : LENS LENS FOCUS MODE FOCUS LIMIT ZOOM START ZOOM STOP ZOOM SPEED E-ZOOM INITIAL RETURN … … … … … … AUTO 50CM X1 X180 V-FAST ON 1. FOCUS MODE • AUTO : Focus is automatically adjusted with moving zoom. • MANUAL : Focus can be manually adjusted, independent of moving zoom. 2. FOCUS LIMIT • Minimum distance the camera can focus. ex) 50 cm: Subjects closer than 50 cm cannot be brought into focus. • 1CM/10CM/50CM/1M/2M/3M/5M/10M/INF 3.
7 .Operating Ca m e r a 5. ZOOM SPEED • Configure zoom tracing speed. • V-FAST(2.8sec)/ FAST(3.4sec)/ NORMAL(4.0sec)/SLOW(6.5sec) 6. E-ZOOM • Configure digital zoom function. • ON : Enable Digital Zoom • OFF : Disable Digital Zoom 7. INITIAL • Initializes the changed category in LENS menu. • Press the NEAR/FAR button to confirm.
7 .Operating Ca m e r a Sub-Menu : EXPOSURE EXPOSURE AE MODE BRIGHTNESS FLICKERLESS SHUTTER AGC LEVEL MAX AGC GAIN MAX FIELDS INITIAL RETURN … … … … … … … SHUT FIX 8 OFF 1/60 MID 128 1. AE MODE • AUTO : Automatic mode. Exposure is controlled by Shutter, Iris & Gain. • SHUT FIX : Shutter priority mode. Exposure is controlled by Iris & Gain. • AGC FIX : Gain priority mode. Exposure is controlled by Shutter & Iris. • MANUAL : Manual mode. 2. BRIGHTNESS • Use this function to adjust image brightness.
7 .Operating Ca m e r a 5. AGC LEVEL • For brighter images, set to the desired value. • Can be changed from OFF to 36dB while in AGC FIX and MANUAL mode. 6. AGC LEVEL • Adjusts the maximum gain mode. • OFF, LOW, MID, HIGH, SUPER 7. MAX FIELDS • Adjusts the maximum accumulation fields. • Can be changed from OFF to 128FLD. 8. INITIAL • Initializes the changed category in EXPOSURE menu. • Press the NEAR/FAR button to confirm.
7 .Operating Ca m e r a Sub-Menu : WHITE BALANCE WHITE BALANCE WB MODE WB CONTROL RED CONT BLUE CONT INITIAL RETURN … … … … MANUAL 30 50 1. WB MODE • ATW : When color temperature is 2400° K~12000 K°, select this mode. • INDOOR : Set color temperature to be 3200°K. • OUTDOOR : Set color temperature to be 5800°K. • PUSH : Color will be automatically adjusted while the MENU button is pressed in the temporary automatic mode.
7 .Operating Ca m e r a Sub-Menu : BLC BLC BLC MODE BLC ZONE BLC LEVEL INITIAL RETURN … OFF … CENTER …4 1. BLC MODE • Compensates for scenes with "BACKLIGHT"conditions. 2. BLC ZONE • Sets backlight compensation weighting zone(BLC ON mode). • Can be selected CENTER, TOP, BOTTOM, LEFT, RIGHT. 3. BLC LEVEL • Sets backlight compensation weighting value(BLC ON mode). • Can be adjusted from 0 to 15. 4. INITIAL • Initializes the changed category in BLC menu. • Press the NEAR/FAR button to confirm.
7 .Operating Ca m e r a Sub-Menu : DAY & NIGHT DAY & NIGHT D&N MODE DETECT MODE DWELL TIME D→N LEVEL N→D LEVEL BURST(NIGHT) INITIAL RETURN … … … … … … AUTO SENSOR 1 SEC 1 Lux 10 Lux ON 1. D&N MODE • Select desired operation mode. • COLOR : Day fix mode. • BW : Night fix mode. • AUTO : Automatically changes COLOR/BW mode according to illuminance. • EXTERNAL : Changes COLOR/BW mode according to external input signal. B/W(HIGH, +5V) COLOR(LOW, GND) 2.
7 .Operating Ca m e r a 5. N→D LEVEL • Sets turnover level from BW to COLOR while in AUTO Mode. • Can be adjusted from 3 Lux to 100 Lux. • It can be adjusted under sets SENSOR mode. 6. BURST(NIGHT) • Select the burst signal ON/OFF when NIGHT(ICR ON) mode. 7. INITIAL • Initializes the changed category in DAY & NIGHT menu. • Press the NEAR/FAR button to confirm.
7 .Operating Ca m e r a Sub-Menu : IMAGE IMAGE ROTATE FREEZE SHARPNESS NEGATIVE INITIAL RETURN … … … … NORMAL OFF 10 OFF 1. ROTATE • NORMAL : Normal image. •H : Use this feature to horizontally inverse the screen. •V : Use this feature to vertically inverse the screen. • H/V : Use this feature to horizontally & vertically inverse the screen. 2. FREEZE • Use this feature to freeze capture an image. 3. SHARPNESS • Increasing this value sharpens object edges.
7 .Operating Ca m e r a Sub-Menu : SPECIAL SPECIAL CAM ID LANGUAGE BAUDRATE TITLE PRIVACY DISPLAY MOTION DETECT INITIAL RETURN … 001 … ENG … 9600 … [┛] … [┛] … [┛] … [┛] 1. CAM ID • Assign an identification number to the camera (0 to 255). 2. LANGUAGE • Displays language can be selected from ENG/CHI/RUS/SPN/GER. • Language for OSD(English, Chinese, Russian, Spanish, German) 3. BAUDRATE • Configure baud rate from 2400/4800/9600/19200/38400 bps. • Serial communication speed (bps) 4.
7 .Operating Ca m e r a SPECIAL Sub-Menu : TITLE TITLE Entry Field ↓ CAM TITLE ----------- Max.10 Character [M] select ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 0 1 2 3 4 5 6 7 8 9 Ä Ö Ü È Æä ö ü á é í ñ ó ú ß æ SPACE>> <> LOCATION RETURN … [┛] 1. Move the cursor to the character entry field using the NEAR or FAR button. 2. Use TELE, WIDE, NEAR, and FAR buttons to select a desired character. 3. Press the MENU button to confirm selection of the blinking character.
7 .Operating Ca m e r a SPECIAL Sub-Menu : TITLE 5. You can select on screen position of the TITLE. • Move the cursor to "LOCATION" and press NEAR/FAR button. • The TITLE is displayed on the top-left of the monitor screen. • Select the position using the TELE/WIDE/NEAR/FAR button. • Press the MENU button to confirm the position and exit this menu. [TITLE LOCATION] [M] ┛ CAM TITLE [T]↑[W]↓[N]←[F]→ 6. When completed, move the cursor to "RETURN" and press NEAR/FAR button.
7 .Operating Ca m e r a SPECIAL Sub-Menu : PRIVACY PRIVACY ZONE NO CONTROL H START V START H WIDTH V HEIGHT MASK COLOR INITIAL RETURN … … … … … … … 3 MASK 10 30 200 110 BLACK 1. ZONE NO • Select the privacy mask zone number(1 ~ 15). 2. CONTROL • Select desired masking effect. • OFF: disable privacy zone as mask or mosaic. • MASK: enable privacy zone as mask. • MOSAIC : enable privacy zone as mosaic. 3. H START • Set the horizontal starting point of privacy zone(0 ~ 180). 4.
7 .Operating Ca m e r a SPECIAL Sub-Menu : DISPLAY DISPLAY CAM ID CAM TITLE CAM STATE ZOOM RATIO MOTION MSG( MD ) POWER ON MSG STANDBY INITIAL RETURN … ON … ON … ON … ON … ON … OFF … ON Use this feature to display the Function-OSD on the screen. 1. CAM ID : Displays camera ID on ⑪ of the screen. 2. CAM TITLE : Displays camera title on ⑨ of the screen. 3. CAM STATE : Displays camera state on ① ~ ⑦ of the screen. 4. ZOOM RATIO : Displays zoom ratio on ⑩ of the screen. 5.
7 .Operating Ca m e r a SPECIAL Sub-Menu : MOTION DETECT MOTION DETECT ZONE NAME CONTROL H START H END V START V END SENSITIVITY ALARM INITIAL RETURN … WINDOW0 … ON … 16 … 88 …9 … 65 …8 … OSD&SERIAL When there is a movement in the monitoring area, there will be an alarm, or the user will be informed through communications or " MD " will display on the screen. 1. ZONE NAME • Select the motion detection area number. • Use the mask displayed on the screen to set positions.
7 .Operating Ca m e r a SPECIAL Sub-Menu : MOTION DETECT 6. V END • Set the vertical starting point for motion detection area. • Select desired position from 6 to 128 in WINDOW0~3. • Select desired position from 0 to 7 in BLOCK. 7. SENSITIVITY • Increase or decrease detection sensitivity value. • Can be set from 1 (low response) to 15 (sensitive). 8. ALARM • Select desired alert type. • OSD : The WINDOW or BLOCK will be displayed on the screen when motion is detected.
8 .
8 .Communicati o n P r o t o c o l Default Protocol Commands Most widely used Commands NOTE • The camera can be controlled by VISCA(SONY), LG, Pelco-P Compatable Protocol. For more detailed informations refer to their manuals.
9 .Specification s Model Signal System Image Sensor CCD PAL 1/3 Inch SONY Super HAD CCD II Total Pixels 811(H) x 508(V) Effective Pixels 768(H) x 494(V) Lens Optics High Res. Zoom NTSC 795(H) x 596(V) 752(H) x 582(V) 18x, f=4.7~84.6mm(F1.6 ~F2.8) Min. Focus Distance 0.01m Digital Zoom Angle Field of View 1x ~ 10x Diagonal : 67.3 degrees(Wide) to 4.0 degrees(Tele) Scanning System Sync. 2:1 Interlace Sync. System Frequency Internal H:15.734 KHz V:59.
