M148-ZAK220-001 220X AUTO FOCUS ZOOM COLOR CAMERA Operation Manual High Resolution WDR - Color Camera with 22x Optical and 10x Digital - Zoom Lens T h a n k y o u f o r cho o si ng o u r hi gh q uality cam er a. Before attempting to connect or operate, please read and fo llo w t h e s e i n structi on s.
Cautions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Cautions Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
Contents Cautions ··························································· 3 1 General··························································· 6 1.1 Product Overview·········································· 6 1.2 Features····················································· 6 1.3 Specifications··············································· 6 1.4 Dimensions·················································· 7 1.
1 GENERAL 1.1 PRODUCT OVERVIEW The is a high resolution color camera equipped with a 22x auto-focus zoom lens and 10 x digital zoom. Many advanced features allow utilizing the in a wide range of CCTV - applications. 1.
1 GENERAL 32.0 64.0 38.2 1.4 DIMENSIONS 66.0 110.
1 GENERAL 1.5 BACK PANEL CONTROLS AND CONNECTORS MENU key Arrow keys T/W/N/F 12V / GND LED Arrow keys N / F MENU key Video output BNC LED Control inputs 12V / GND D/N Video output BNC GND 485- FOCUS COM 485+ Arrow keys T / W ZOOM Control inputs Buttons for zoom control, in OSD menu row selection up/down Buttons for focus control, in OSD menu change of parameters Open/close OSD setup menu Video output BNC, composite 1 Vs-s / 75 Ohm LED on indicates power on.
2 INSTALLATION 2.1 POWER Connect a stabilized 12 VDC power supply (500mA or higher) to the power terminal. 2.2 VIDEO INTERMEDIATE END MONITOR VIDEO VIDEO Connect the video output (BNC) with 75 Ohm video coax cable with DVR, monitor or other equipment with video input. Please take care for correct 75 Ohm termination.
2 INSTALLATION 2.3 REMOTE CONTROL The camera provides an input for RS-485 control with Pelco-D/ P protocol. Further on the lens can be controlled by control devices with 5 VDC voltage (PTZ-receiver, control keyboards with DC output). The day / Night mode can be switched by an external contact. 2.3.1 RS-485 Connect the RS-485 input with twisted pair cable to the control device. For details of RS-485 wiring please consult the related chapters in user manuals of DVRs or control keyboards.
2 INSTALLATION 2.3.3 DC-Lens control The lens can be controlled by control devices with 5 VDC voltage (PTZ-receiver, control keyboards with DC output). Please check the control device to correct output voltage (+/- 5VDC max). 2.3.3 Day- / Night switching The day/night switching can be controlled by an external dry contact. Closing the contact (to GND) will turn the camera in night mode. In OSD menu DAY&NIGHT the item MODE needs to be set to EXTERNAL.
3 CAMERA SETUP Zoom tele Focus near Focus far MENU Zoom wide 3.1 ZOOM The key T is used for zoom in, W for zoom out. 3.2 FOCUS The key N focuses the lens in near distance, F key focuses in far distance.
3 CAMERA SETUP 3.3 OSD SETUP MENU 3.3.1 OSD display NO Function Format Description Auto Focus Interval AF Focus Zoom Trigger AF NO ③ Manual Focus WB BLC HSBLC Night Freeze Motion Detected Optical Zoom Digital Zoom Camera ID AWB ⑤ LOADING... Standby message ⑥ Title Max.
3 CAMERA SETUP 3.3.2 Menu Structure SETUP 1. FOCUS 2. EXPOSURE 3. WHITE BAL 4. D-WDR/BLC 5. DAY&NIGHT 6. IMAGE 7. SPECIAL 8. RESET 9. EXIT ┛ ┛ ATW OFF AUTO ┛ ┛ OFF ┛ FOCUS FOCUS MODE ZOOM START ZOOM STOP ZOOM SPEED D-ZOOM MIN. DIST RETURN AF INTERVAL ZOOM TRIG .|...... 1 ….. | 220 FAST ON 50CM ┛ RUN TIME INTERVAL RETURN ..| … 10 ..| …… 60 ┛ IRIS MANUAL EXPOSURE SHUTTER IRIS AGC MAX. AGC MAX. FIELD BRIGHT RETURN LEVEL RETURN OFF AUTO AUTO MIDDLE OFF …….. |…. 50 ┛ ..|……..
3 CAMERA SETUP D&N VIDEO D&N AUTO DAY & NIGHT DETECT MODE DWELL TIME BURST RETURN VIDEO ┛ ..|…… 5 ON ┛ D->N LEVEL D<- N LEVEL RETURN ….|.... 176 ….|.... 76 ┛ SMART IR AREA SMART IR H. START V. START WIDTH HEIGHT RETURN IMAGE SMART IR 3DNR FREEZE ROTATE SHARPNESS NEGATIVE RETURN ┛ ┛ OFF OFF ..|… 15 OFF ┛ GAIN AREA RETURN ….|.... ┛ ┛ 001 9600 ENG ┛ ┛ ┛ ┛ ┛ 3 2 2 3 ┛ 3DNR LEVEL RETURN ….. |….
3 CAMERA SETUP 3.3.3 Setup - Menu Operation MENU Press the key MENU for opening the OSD setup menu. The screen shows the main setup menu. NEAR / FAR TELE / WIDE SETUP 1. 2. 3. 4. 5. 6. 7. 8. 9. FOCUS EXPOSURE WHITE BAL D-WDR/BLC DAY&NIGHT IMAGE SPECIAL RESET EXIT 」 」 ATW / AWB / PWB」/ MWB」 / IWB / OWB OFF / D-WDR」 / BLC」 / HSBLC」 AUTO」 / COLOR / BW / EXTERNAL 」 」 OFF / ON」 」 The keys T / W move the cursor vertical between the rows, changing parameters and values is done by the FOCUS - keys N / F.
3 CAMERA SETUP 3.3.3.1 FOCUS FOCUS FOCUS MODE ZOOM START ZOOM STOP ZOOM SPEED D-ZOOM MIN. DIST RETURN AUTO/INTERVAL」/ZOOM TRIG/MANUAL ...l... 1 ~ 22 ...l... 1 ~ 220 SLOW / NORMAL / FAST / V.FAST OFF / ON 1CM/10CM/50CM/1M/2M/3M/5M/10M/INF 」 FOCUS MODE Focus operation mode AUTO Auto focus permanent on. INTERVAL The focus will be checked in intervals in the range 3~255 s (setup in line INTERVAL) for a defined duration (3 ~255s, setup in line RUN TIME).
3 CAMERA SETUP 3.3.3.2 EXPOSURE EXPOSURE SHUTTER IRIS AGC MAX. AGC MAX. FIELD BRIGHT RETURN 256FLD / ... / 2FLD / AUTO / OFF / FLK / ... / 1 / 100000 AUTO / MANUAL」 AUTO / MANUAL」 OFF / LOW / MIDDLE / HIGH / SUPER OFF / 2FLD / 4FLD / ... / 256FLD ···l··· 1 ~ 100 」 SHUTTER AUTO: Automatic shutter FLK: Flickerless mode 1:160~1/100.
3 CAMERA SETUP 3.3.3.3 White Balance WHITE BAL MODE PUSH RED BLUE RETURN ATW 」 MODE Operation mode of white balance ATW: Automatic White Balance in temperature range 2400°K to 12000°K AWB: Temperature range is broader than ATW.
3 CAMERA SETUP 3.3.3.4 D-WDR/BLC D-WDR / BLC MODE LEVEL AREA DISP. MODE RETURN D-WDR ···l··· 9 」 Mode: D-WDR Digital Wide Dynamic Range for balancing strong light differences in scenery Level Adjustment of WDR level D-WDR / BLC MODE LEVEL AREA DISP. MODE RETURN BLC AREA BLC MIDDLE 」 」 H. START V. START WIDTH HEIGHT RETURN 3 2 2 3 」 Mode: BLC Back Light Compensation, dark objects enclosed with backlight will be brightened.
3 CAMERA SETUP D-WDR / BLC MODE LEVEL AREA DISP. MODE RETURN HSBLC ···l··· 4 」 ALL DAY 」 Mode: HSBLC Highlight suppression, strong light sources (e.g. car lamps) will be blacked out in image Level Sensitivity trigger level in 9 steps Area Adjustment of monitored area for HSBLC in a grid 8x8 H.START: Position of 1. field of area from left (0~7) V.START: Position of 1.
3 CAMERA SETUP 3.3.3.
3 CAMERA SETUP 3.3.3.
3 CAMERA SETUP 3.3.3.7 SPECIAL SPECIAL CAM ID BAUDRATE LANGUAGE TITLE PRIVACY MOTION OSD SET RETURN 001 9600 ENG 」 」 」 」 」 CAM ID RS-485 address of camera, range 0~255 BAUDRATE Baud rate of RS-485 transmission, 2400, 4800, 9600, 19200 or 38400. Control commands for OSD - menu (Pelco-D/P protocol).
3 CAMERA SETUP PRIVACY Privacy zone adjustment, up to 8 areas can be masked. PRIVACY MASK NO DISP MODE AREA COLOR TRANSPARENT RETURN 1 INT.LOCK 」 C0 OFF 」 MASK NO: Selection privacy zone 1~8 for setup. DISP MODE: OFF: Privacy zone not active. NON.LOCK / INT.LOCK: Privacy zone active. AREA: WIDTH: Width of privacy zone. HEIGHT: Height of privacy zone. PAN POSI: Position horizontal. TILT POSI: Position vertical. ZOOM POSI: Setup zoom position / test. MASK RESET: Removing of mask.
3 CAMERA SETUP OSD SET Display options OSD SET CAM ID ZOOM MAG FUNC OSD OSD COLOR RETURN OFF OFF OFF C3 」 CAM ID: The RS-485 address will be displayed. ZOOM MAG: In case of lens operation the zoom position appears for 5 s. FUNC OSD: In case of lens operation the status icons appear for 5 s. OSD COLOR: Color setup for OSD menu. 3.3.4 RESET All settings of the camera will be initialized and set to factory defaults.
