User's Manual

Product name
Serial number
Purchase Date
T102K - TW
20 , , ,
Installation Company
Installer
Contact
* Note: Please keep your warranty note above for warranty service.
1. The warranty for this product is covered by the warranty as above stated.
2. The warranty period is one year from the purchase.
Product Warranty
While locking/unlocking,
the motor will stop in the middle
and the lock beeps.
Door lock does not respond
upon touching the number pad.
When the door is closed,
the automatic lock doesn’t work.
When opening and closing the
door, there is a feeling of
shaking or getting stuck.
Replace all batteriesBattery issue
Deadbolt jamming due
to damaged door and door frame
Safe mode due to multiple
password input
The door close sensor may not
have been installed or defective.
The fixing screw for the door
lock or striker may have been
loosened.
Check/adjust the door closer between
the door and door frame.
Try again in about 3 minutes.
Verify if the door close sensor is
installed or contact
KT&C customer service.
Check all fixing screws and try using
glue as needed.
◇ This function will toggle between activate and deactivate using the same command.
7
How to Use
8
How to Use
9
How to Use
After removing all used batteries,
insert the AA alkaline batteries according to the polarity.
◇ You must use alkaline batteries.
◇ When replacing batteries, replace all batteries at the same time.
◇ A leak from the battery may damage the product.
Please check the battery status every 6 months.
This function is for the administrator to manage the master password.
Register
Modify
Delete
◇ A password that’s the same as the master password cannot be registered.
◇ The master password cannot be used to unlock the door.
◇ When the master password is deleted,
you can proceed with registering procedure without entering the master number.
●
When a low voltage (below 4.2V) is detected,
a low voltage alarm sounds after the door lock operation.
●
The [
1
], [
4
], [
7
], [
8
], and [
9
] LEDs on number pad flashes while the
melody occurs and then turns off.
The low voltage alarm will continue to make a sound until the voltage from
the battery becomes 5.7V or higher.
In open state, hold down [ Registration ] Button for 3 seconds + [2]
+
Master password (4~10 digits) + [ ].
In open state, hold down [ Registration ] button for 3 seconds + [2]
+
registered master password + [ ] + new master password (4~10 digits) + [ ].
In open state, hold down [ Registration ] button for 3 seconds + [5]
+ registered master password + [#] + [ Registration ] button for 3 seconds.
Master Password
Low Voltage Alarm
Battery Replacement
11
FCC
12
Confirmation
▶ The contents of this manual may be changed without prior notice to improve the function and
quality of the product.
Ver 1.0
Troubleshoot
ActionSymptom Possible Cause
After password authentication,
[1],[4],[7],[8].[9] on the number
pad will be lit and a melody
sounds.
KTNC - T 1 0 2 K
BLE Communication Module (Optional)
Open the battery cover and connect BLE Module to its connector.
[OPEN/CLOSE via BLE]
●
Upon execution of the KeyWe app,
it will establish a connection with the
BLE module.
● Once connection is successful,
the app will display the status of the
door lock on the screen.
● If the user clicks the center area of
the screen, the door Lock status will
change.
● For further information,
refer to below Link. [https://thekeywe.blog/category/app-user-guide/]
[Door Lock Registration
and How to use]
◇ It will only work on iOS 8 or later and Android 4.4 or later.
◇ The operation may not be smooth when the smartphone OS is not compatible.
1. Search for‘Keywe’from Play Store
or APP Store and Install.
2. Sign up in the app.
3. From the menu located upper
left select‘Connect Door Lock’.
4. Click‘+’sign in the middle of
registration screen and then select
‘QR Code’registration.
6. Click‘Confirmation’button to complete.
5 . Scan the QR CODE to register the
BLE Module.
Intrusion Alarm
Destructive Alarm
◇ In the event of an alarm, hold down [Registration] button for more than 3 seconds
or enter the password on the number pad to stop.
Intrusion/Destructive Alarm
Deadbolt Jam Notification
Temporary Password (One-Time Password)
It will make a high-pitched alarm sound upon abnormal door
opening while the door is locked.
It will make a high-pitched alarm sound upon the detection of
damage or abnormal detachment of the unit.
◇ The intrusion alarm function is not available when the door close sensor
is not installed.
◇ When activated, 3 random numbers on the number pad will be lit.
Once you select those numbers, all numbers on the number pad will be lit so that
you can enter the password.
◇ The temporary password is valid for once.
◇ The temporary password length is fixed at 5 digits.
◇ It can be set only when the door is locked.
The registered temporary password will automatically be deleted after
a single-use.
If the deadbolt does not properly open or close,
the door lock will make 2 more attempts before an error alert.
This function is used to prevent security risk caused by residual fingerprints
on the number pad.
In close state, touch the number pad, enter the password
+ [#] + [#]
+ 5-digit temporary password +
[ ]
◇ If the communication pack (BLE module) is installed,
a temporary password cannot be created at the door lock.
It can only be created from the remote app.
Dual Password On/Off
In open state, [ Registration ] Button ( 3 seconds ) + [4]
+ [ Registration ] Button
In open state,
[ Registration ] Button ( 3 seconds ) + [4]
+ [ Registration ] Button
Set
Delete
Activate
Deactivate
10
MEMO
Radiation Exposure Statement:
Federal Communication Commission
Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority
to operate this equipment. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.