Installation Guide 10/100 Fast Ethernet Switch with 100FX Connectivity KS-108F Ver.B Series DOC.
(C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.
The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including the interference that may cause.
Table of Contents 1. Introduction .................................................................. 5 1.1 Features ........................................................................................... 6 1.2 Specifications .................................................................................. 7 2. Installing the Switch ..................................................... 9 2.1 Unpacking ....................................................................................... 9 2.
1. Introduction This 8-port Fast Ethernet switch series provides seven 10/100 TP ports and one 100BASE-FX fiber port, each capable of transmitting or receiving information simultaneously at full wire speed to control and allocate the network bandwidth.
1.1 Features Designed for resolving congestion problems caused by bandwidth-hungry devices and bandwidth-intensive applications as well as a high number of users, the switches not only adhere to the IEEE 802.3 10BASE-T, 802.3u 100BASE-TX and 100BASE-FX standards, but also feature: • • • • • • • • • • Seven 10/100BASE-TX auto-negotiation switched ports and one 100BASE-FX port for flexible connections to desktop PCs, servers and Fast Ethernet devices.
1.2 Specifications 10/100 Ports IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX std. Shielded RJ-45 jacks with Auto MDI-X detection Auto-negotiation capable Speed for 10Mbps or 100Mbps Full-duplex or half-duplex mode support 100FX Port IEEE 802.3u 100BASE-FX compliant Fixed 100Mbps operation Duplex mode selector - full duplex or half duplex Flow control IEEE 802.3x pause packet for full duplex operation Back-pressure for half duplex operation Cables 10BASE-T Cat. 3, 4, 5 or higher (100 meters max.
100FX Port Fiber Specifications KS-108FB-xxx Duplex Series Model Ext -T -C -JM -VM -SA2 -SL2 -SL3 -SL4 -SL6 -SL7 -SL9 -SL10 -SL12 Fiber Wavelength ST MMF 1310nm SC MMF 1310nm MT-RJ MMF 1310nm VF-45 MMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1310nm SC SMF 1550nm SC SMF 1550nm Tx Power -19 ~ -14dBm -19 ~ -14dBm -19 ~ -14dBm -20 ~ -14dBm -15 ~ -8dBm -15 ~ -8dBm -15 ~ -8dBm -5 ~ 0dBm -5 ~ 0dBm -3 ~ +3dBm 0 ~ +5dBm -3 ~ +3dBm 0 ~ +5dBm Sens. Ref.
2. Installing the Switch 2.1 Unpacking Check to see that you have everything before you start the installation. • Installation guide • The switch unit • One AC power adapter for the unit 2.2 Checking AC Power Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area.
The DC power jack for the AC power adapter is located on the rear of the switch as shown below: 2.3 Installing the Switch 1. Install the switch with the AC power adapter provided. 2. Connect the power adapter cable to the switch before connecting the adapter to the AC outlet.
3. Making Network Connections 3.1 Switched Ports The following figure shows the locations of the switched ports: 3.
Cables Depending on the connection speed, use the proper UTP cables: Speed 100M 10M Cables used Distance Cat. 5, 5e, or higher grade 100 meters Cat. 3, 4, 5, 5e, or higher grade 100 meters Auto-MDI-X Function An Auto-MDI-X function will automatically detect if a crossover is required and make the swap of Tx pair and Rx pair internally. With this function, straight-through cable can be used for any connection. MDI to MDI-X connection rule is not necessary anymore.
100FX Duplex Selector This selector is used for 100FX port duplex mode selection as follows: The following table lists the maximum MM fiber cable length connecting to different devices: Connected Device Network card half-duplex fiber port Network card full-duplex fiber port Class I hub half-duplex fiber port 2 Class II hub half-duplex fiber port Switched half-duplex fiber port Switched full-duplex fiber port -13- Distance (MMF cable) 400 m 2 km 160 m 112 m 400 m 2 km
4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing and monitoring the operation of the switch as illustrated below: 4.2 Interpretation LED Functions POWER LED : indicates the power status of the switch.
