User’s Manual CCTV COLOR TFT LCD TVLCD MONITOR
Important Safety Instructions ...................................... 3 FCC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety Notices ................................................................ 6 Location controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functions and control methods . . . . . . . . . . . . . . . . . . . . . . . . . .
Shock Hazard Marking and Associated Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Explanation of Safety Related Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
SAFETY NOTES Thank you for purchasing our product# Before using it please read this user's manual carefully and apply it correctly and safely# Please keep this manual close to you so you can refer to it anytime after reading it# Also for the transportation of the product please attach this manual without fail# Please observe the notes below# 1. Use at the rated power voltage# Use of non1rated voltage may cause fire electric shock and breakdown# 2.
SAFETY NOTES 17. Do not install at the place with moisture or dust# It may cause the fire or the electric shock 18. Do not install it at the place with poisonous gas# It may cause the fire# 19. Do not install it at the location with continuous vibration# It may be tipped over as it loses balance or damaged as it is fallen down# 20.
6# POWER # POWER LED LAMP (STAND BY) # PC # S1VIDEO 2# VIDEO 8# VIDEO 6 <# VOLUME DOWN/UP :# SELECT B# MENU 67# CONTRAST 66# BRIGHT 6 # COLOR 6 # TINT 6 # VIDEO IN (CH6) 62# VIDEO OUT (CH6) 68# VIDEO IN (CH ) 6<# VIDEO OUT (CH ) 6:# AUDIO IN (CH6) 6B# AUDIO OUT (CH6) 7# AUDIO IN (CH ) 6# AUDIO OUT (CH ) # S1VIDEO # PC # DVI 2# AC INLET 8# KENSINGTON LOCK HOLE LCD Monitor : User’s Manual
1. POWER BUTTON : Press to turn the LCD monitor ON. The POWER LAMP above the switch will illuminate. 2. POWER LED LAMP : When SET is normally operated, a green lamp is turned on. The green lamp flickers in the status of STAND-BY. STAND BY : ON/OFF BUTTON is off 3. PC BUTTON : When you press this button, PC mode is selected. 4. S-VIDEO BUTTON : When you press this button, S-VIDEO mode is selected. If you want to see a clean and clear video through S-VIDEO input, select this. 5.
MENU Operation When you press the MENU button, the MENU window appears on screen. Press SEL BUTTON to move to the desired item. Press VIO+ key to select the desired item. To shut down the MENU window, wait for time when the MENU window disappears or press the MENU button again. MENU in VIDEO1, VIDEO2, and S-VIDEO It shows the MOVE button, SEL button, and EXIT button on a bottom of MENU window. COLOR TEMP 9300/6500 MAIN MENU COLOR TEMP UTILITY OSD LANGUAGE You can select a temperature of desired color.
MENU in PC When you press the MENU Button, the MENU screen appears. It shows a resolution, vertical and horizontal frequency of current monitor on the bottom of MENU Window. AUTO ADJUST Adjust the screen s status in PC mode automatically. MAIN MENU AUTO ADJUST SCREEN COLOR UTILITY OSD LANGUAGE SCREEN BRIGHTNESS Adjust the screen s brightness CONTRAST Adjust the screen s contrast H.POSITION Adjust the screen s horizontal position V.
Outlet This monitor can Plug be available regardless of 667V/ 7V# Conversion plug Be sure to connect the conversion plug to the power plug by the outlet! This monitor can be available both in AC 667V / 7V 87Hz Various input voltage (within a range of AC677; 7V) can be available# (Do not use it in the voltage higher than a rated voltage) 667V/ 7V selector switch is not necessary# This monitor can be operated directly without a special operation# CAUTION Make sure to operate this monitor in the ra
Read the installation/operation manual thoroughly before connecting equipment. Turn off the power source before connecting the monitor and external equipment.
If your monitor is out of order, check up the below problems firstly. The screen doesn't appear and the sound is not heard# The sound is heard but the video doesn't appear# Is the power cord pulled out? Is the power turned off? Is this monitor connected with the external equipment erroneously? Connect the power cord correctly Press the power button. Check the cord and then connect it correctly.
This monitor has received the EMI (Electromagnetic interference) test for the business. Accordingly, a seller or user needs to know about it. If you purchase the erroneous monitor, be sure to exchange it into non-business monitor in the shop where you buy it.
