Operation Manual
•Changing
Front
Axle
Case
Oil
1.
Park
the
tractor
on
a firm, flat
and
level
surface.
2. To drain
the
used
oil,
remove
the
right
and
left drain
plugs
and
filling plug
at
the
front
axle
case
and
drain
the
oil
completely
into
the
oil
pan.
3. After draining, reinstall
the
drain plugs.
4. Fill with
new
oil up to
the
upper
notch
on
the
dipstick.
(See
"LUBRICANTS" in "MAINTENANCE" section)
IMPORTANT:
• After 10 minutes,
check
the
oil level again;
add
oil to
prescribed
level.
5. After filling, reinstall
the
filling plug.
6.
Properly
dispose
of
used
oil.
Oil
capacity
3.5
L
(3.7
U.S.qts.)
1AGAEEIAP026A
(1) Filling
plug
with dipstick
(2) Drain
plug
EVERY
800
HOURS
(A) Oil
level
is
acceptable
within
this
range
•Adjusting
Engine
Valve
Clearance
Consult
your
local KUBOTA
Dealer
for this
service.
EVERY
1 500
HOURS
•
Checking
Fuel
Injection
Nozzle
Injection
Pressure
Consult
your
local KUBOTA
Dealer
for this
service.
EVERY
3 000 HOURS
•Checking
Injection
Pump
Consult
your
local KUBOTA
Dealer
for this
service.
PERIODIC
SERVICE
67
EVERY
1 YEAR
•
Replacing
Air
Cleaner
Primary
Element
and
Secondary
Element
(See
"Cleaning Air
Cleaner
Primary Element" in "EVERY
100 HOURS" in "PERIODIC SERVICE" section.)
IMPORTANT:
• To prevent serious
damage
to
the
engine,
use
only a
KUBOTA
genuine
filter.
EVERY
2
YEARS
•
Flushing
Cooling
System
and
Changing
Coolant
A
WARNING
To
avoid
personal
injury
or
death:
• Do
not
remove
radiator
cap
while
coolant
is
hot.
When
cool,
slowly
rotate
cap
to
the
first
stop
and
allow
sufficient
time
for
excess
pressure
to
escape
before
removing
the
cap
completely.
1.
Stop
the
engine,
remove
the
key
and
let it cool
down.
2.
To
drain
the
coolant,
disconnect
the
radiator
hose
(engine
side),
and
remove
the
radiator
cap.
The
radiator
cap
must
be
removed
to
completely
drain
the
coolant.
3.
After
all
coolant
is
drained,
reconnect
the
radiator
hose.
4. Fill with
clean
soft
water
and
cooling
system
cleaner.
5.
Follow
directions
of
the
cleaner
instruction.
6. After flushing,
fill
with
clean
soft
water
and
anti-freeze
until
the
coolant
level is
just
below
the
radiator
cap.
Install
the
radiator
cap
securely.
7. Fill with
coolant
up to
the
"FULL"
mark
of
recovery
tank.
8.
Start
and
operate
the
engine
for few
minutes.
9.
Stop
the
engine,
remove
the
key
and
let cool.
10.
Check
coolant
level of
recovery
tank
and
add
coolant
if
necessary.
11.
Properly
dispose
of
used
coolant.
Coolant
capacity
(with
recovery
tank)
3.8
L
(4.0
U.S.gals.