Installation Instructions
06/27/97
11:
37
~1
310 370
4186
KUBOTA
TRACTOR
-H->
SE
SERyICE
(CORRECTED)
.~
"
B203P032
(1)
Brake
Rod (RH)
(7)
Adjusting
Nut
(2)
HST
Pediil
Damper
(B)
lock
Nut
(3)
Neutral
Adjuster
(9)
lod:
Nut
(4)
Return
Spring
(for
(lO)
lod:
Nut
forward
adjustment)
(11)
Neutral
Position
(5)
Return
Spring
(for
Adjusting
Nut
reverse
adjustment)
(12)
Rod
(6)
Adjusting
Nut
(13)
Stay
(32142)
Bulletin
No:
SFI-A-97-008
Adjusting
Neutral
1.
Disconnect
the
brake
rod
RH
(1). .
2. Loosen
the
lock
nut
(B)
(9)
and
adjusting
nut
(6) (7)
until
springs
(4) (5)
are
freely.
3.
Loosen
the
lock
nut
(10)
and
neutral
position
adjusting
nut
(11) until
washer
welded
on
the
rod
(12)
comes
off
from
stay
(13).
4.
Remove
the
HST
pedal
damper
(2).
5. Loosen
the
neutral
adjuster
(3)
setting
screw.
(When
rear
wheels
tend
to
turn
forward)
1.
Rotate
the
neutral
adjusting
lever
clockwise
so
that
the
rear
wheels
turn
reverse.
2.
Then
rotate
it
counterclockwise
until
wheels
stop
completely.
(When
rear
wheels
tend
to
turn
reverse)
1.
Rotate
the
neutral
adjusting
lever
counterclockwise
so
that
the
rear
wheels
turn
forward.
2.
Then
rotate
it
clockwise
until
wheels
stop
completely.
(After
adjusting
neutral)
1.
Make
sure
the
HST
control
pedal
(d)
is
at
the
neutral
position.
(Let
the
pedal
go
from
the
forward
to
the
neutral
position,
as
well
as
from
the
rearward.to
the
neutral
position.
Make
sure
the
pedal
returns
to
just
the
same
neutral
position.)
2.
Turn
the
neutral
position
adjusting
nut
(11)
to
move
the
rod
(12)
until
there
is
a
clearance
"A"
0
mm
(0 in.)
between
the
welded
washer
and
the
stay
(13).
(Set
in
position
with
a
slight
contact.)
Now
turn
this
nut
counterclockwise
by
half
a
turn.
Now
lock
the
nut
(10). (Be
careful
not
overtighten
the
nut
(11).
Otherwise
the
H5T
pedal
may
get
stuck.)
3. Finally lock
the
double
nut
(8), (9)
so
that
the
spring
(4), (5),
should
be
64
to
66
mm
(2.5
to
2.6 in.)
forward
and
64
to
66
mm
(2.5
to
2.6 in.)
rearward
in
length
Band
C.
---
length
(B)
length
(e)
Normal
compression
65
mm
{2.6
in,)
65
mm
(2.6
In.)
Max.
compression
42
mm
(1.7
in.)
42
mm
(1.7
in.)
I
Neutral
adjuster
setting
39.2
to
44.1
N'm
Tightening
torque
4.0
to
4.5I<gf·m
screw
28.9
to
32.5
ft-Ibs
KUBOTA Corporation, OSAKA, JAPAN