OPERATOR'S MANUAL
Table Of Contents
- OPS - Utility Vehicle RTV1140CPX (K7611-7121-5)
- Abbreviation List
- Introduction
- Universal Symbols
- Foreword
- Safety First
- Contents Page
- Safe Operation
- Servicing of Vehicle
- Specifications
- Vehicle Limitations
- Instrument Panel and Controls
- Pre-Operation Check
- Operating the Engine
- Operating the Vehicle
- Seating and Cargo Bed
- Tires and Wheels
- Towing and Transporting
- Maintenance
- Periodic Service
- How to Open the Hood and Tilt the Seat
- How to Raise the Carbo Bed
- Jack Up Point
- Daily Check
- Walk Around Inspection
- Checking and Refueling
- Checking Engine Oil Level
- Checking Hydraulic Tank Oil Level
- Checking Transmission Fluid Level
- Checking Coolant Level
- Cleaning Radiator Screen
- Checking Brake Fluid Level
- Checking Brake Pedal
- Checking Parking Brake
- Checking Gauges, Meter and Easy Checker
- Checking Head Light, Turn Signal Light etc
- Checking Seat Belt and ROPS
- Checking Joint Boot
- Checking Tire Inflation Pressure
- Checking Backup Beeper
- Every 50 Hours
- Every 100 Hours
- Every 200 Hours
- Changing Engine Oil
- Adjusting Parking Brake
- Replacing Engine Oil Filter
- Replacing Transmission Oil Filter - HST
- Replacing Transmission Oil Filter - Suction
- Changing Hydraulic Tank Oil
- Checking Brake Pedal
- Checking Brake Hose and Pipe
- Checking Front Brake Case
- Checking Brake Light Switch
- Checking Radiator Hose and Clamp
- Checking Power Steering Line
- Checking Intake Air Line
- Every 300 Hours
- Every 400 Hours
- Every 500 Hours
- Every 800 Hours
- Every 1500 Hours
- Every 3000 Hours
- Every 1 Year
- Every 2 Years
- Every 4 Years
- Service As Required
- Storage
- Troubleshooting
- Options
- Index
PERIODIC SERVICE70
BReplacing Hydraulic Tank Oil Filter
To avoid personal injury:
A Be sure to stop the engine before changing the
oil filter cartridge.
A Allow engine to cool down sufficiently, oil can
be hot and can burn.
1. Park the vehicle on a firm, flat and level surface.
2. Tilt the seat.
3. Remove the oil filter. (Take care of the oil that spills
from filter.)
4. Put a film of clean KUBOTA SUPER UDT OIL on the
rubber seal of the new filter.
5. Quickly tighten the filter until it contacts the mounting
surface, then, with a filter wrench, tighten it an
additional 1 turn only.
6. After running the engine for a few minutes, stop the
engine and check the oil level, add oil to the prescribed
level.
7. Make sure that the hydraulic tank oil doesn't leak past
the seal on the filter.
A Receive the spilt oil with rags or trays.
Be careful not to spill oil.
If you should spill oil, wipe it off at once.
A To prevent serious damage to the hydraulic line, use
only a KUBOTA genuine filter.
BChanging Front Axle Case Oil
1. Park the vehicle on a firm, flat and level surface.
2. To drain the used oil, remove the drain and filling plugs
at the front axle case and drain the oil completely into
the oil pan.
3. After draining, reinstall the drain plug.
4. Fill with the new oil up to the upper notch on the
dipstick.
(See "LUBRICANTS, FUEL AND COOLANT" in
"MAINTENANCE" section.)
5. After filling, reinstall the filling plug.
(1) Hydraulic tank oil filter (Return)
Oil capacity 0.6 L (0.6 U.S.qts.)
(1) Drain plug
(2) Filling plug with dipstick
(A) Oil level is acceptable
within this range