www.kucht.
Installation Instructions Dishwasher FOR MORE DETAILS AND INFORMATION, PLEASE VISIT OUR WEBSITE WWW.KUCHT.COM BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT– Observe all IMPORTANT – The dishwasher MUST be installed to allow for future removal from the enclosure if service is required. If you received a damaged dishwasher, you should immediately contact your dealer or builder. governing codes and ordinances.
Installation Preparation PARTS SUPPLIED: Four flat head wood screws to secure dishwasher to underside of countertop (in literature package). Screw type hose clamps and one drain hose. 2@side mounting clips. 2 top mounting cl\ips.
Installation Preparation PREPARE DISHWASHER ENCLOSURE 24”(609.6mm) 34-1/2”(876.3mm) to 35”(889mm) 4“(101.6mm) 6“(152.4mm) 24”(609.6mm) Floor must be even with room floor. Plumbing and Electric Service Must Enter Shaded Area • The dishwasher must be installed so that the drain hose is no more than 10 feet(3.05mm) in length for proper drainage. • The dishwasher must be fully enclosed on the top, side and back, and must not support any part of the enclosure.
Installation Preparation PREPARE ELECTRICAL WIRING WARNING: FOR PERSONAL SAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. 1-1/2”(38.1mm) Dia Hole 3“(76.2mm) Electrical Requirements: • This appliance must be supplied with 120V / 60 Hz., and connected to an individual properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. • Wiring must be two wire with ground.
Installation Preparation PREPARE HOT WATER LINE: • The hot water line may enter from either side, rear or floor within the shaded area shown in Fig. 6 • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2”(38.1mm) dia. hole to accommodate the water line. STOP BEFORE YOU BEGIN Locate and set aside the package containing the 2 Phillips Head Countertop Mounting Screws.
Installation Instructions STEP 6 INSTALL DRAIN HOSE STEP 8 SLIDE DISHWASHER PARTIALLY INTO CABINET • Install the screw type hose clamps to the drain hose. • Install the drain hose to the drain hose installation hose, then tighten the screw type hose hose. DO NOT PUSH AGAINST FRONT PANEL WITH KNEES. DAMAGE WILL OCCUR. • Slide dishwasher into the opening a few inches at a time. Do Not Push Against Front Door Panel With Knee. Damage to The Door Panel Will Occur.
Installation Instructions STEP 9 POSITION DISHWASHER UNDER COUNTERTOP Reposition Dishwasher by Grasping Both Sides With Hands • Check to be sure that wires are secure under the dishwasher and not pinched or in contact with door springs or other dishwasher components. TIP: Check tub insulation blanket, if equipped. It should be positioned so it is not bunched up or interfering with door springs. Check by opening and closing the door. • Push dishwasher into cabinet.
Installation Instructions Open the door remove the tub cap on both sides of the tub. Install screw through the dishwasher side hole to the wall of cabinet. Reinstall tub cap. STEP 11 SECURE DISHWASHER TO THE COUNTERTOP For countertops made of wood or that will not be damaged by drilling,use Method 1. For countertops made of granite,marble,or other materials that could be damadged by drilling,use Method 2. Installation bracket Screw IMPORTANT – Drive screws straight and flush.
Installation Instructions STEP 12 CONNECT DRAIN LINE FOLLOW ALL LOCAL CODES AND ORDINANCES The drain hose molded end will fit 5/8”(15.9mm), 3/4”(19.1mm) or 1”(25mm)diameter connections on the air gap, waste tee or disposer. Cut the marked line as required for your installation. • If a longer drain hose is required, add up to 42” (1067mm) length for a total of 10ft.(3.05mm) to the factory installed hose. Use 5/8”(15.9mm) or 7/8”(22M) inside diameter hose and a coupler to connect two hose ends..
Installation Instructions STEP 14 CONNECT POWER SUPPLY STEP 15 PRE-TEST CHECKLIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover “A”. • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box “B”.
Installation Instructions STEP 16 DISHWASHER WET TEST STEP 17 REPLACE TOEKICK Turn on power supply (or plug power cord into outlet, if equipped). Turn on your dishwasher (please refer to the Owner's Manual for instructions). Close door, select RINSE ONLY cycle and press START/CANCEL. . Check to be sure that water enters the dishwasher If water does not enter the dishwasher, check to be sure that water and power are turned on. Check for leaks under the dishwasher.
WE TRANSFORM A SIMPLE KITCHEN INTO A PRO ONE. THIS IS WHY WE CARE ABOUT MAKING VERY HIGH PERFORMANCE RANGES AND HOODS, TO MAKE YOU FEEL LIKE A PRO AND STYLISH COOKER. DESIGN: LONDON DC - WWW.LONDON-DC.COM FOR MORE DETAILS AND INFORMATION, PLEASE VISIT OUR WEBSITE WWW.KUCHT.