www.kucht.com BE A PRO IN YOUR KITCHEN DUAL-ZONE WINE COOLER INSTALLATION GUIDE AND USER MANUAL APPLICABLE MODEL: K148AH2, K148E1, K280A1, K280AH2, K280AH4, K280AV2, K280AVH3, K430A1, K430AH2, K430AH4, K430AV2, K430AVH3 & K430AVT3.
INSTALLATION GUIDE AND USER MANUAL Contents SAFETY INFORMATION & WARNINGS ......................................................... 3 PARTS AND FEATURES................................................................................. 4 ASSEMBLY INSTRUCTIONS .......................................................................... 5 INITIAL SETUP ........................................................................................... 5 INSTALLATION OF YOUR APPLIANCE .....................................
INSTALLATION GUIDE AND USER MANUAL SAFETY INFORMATION & WARNINGS Before Using Your Wine And Beverage Cooler for the First Time: Carefully read all instructions before using this wine and beverage cooler for the first time. Also make sure the wine and beverage cooler stays in an upright position during transportation. After removing the appliance from its packaging, make sure it is in good condition. If there are any issues with the wine and beverage cooler, please contact us immediately.
INSTALLATION GUIDE AND USER MANUAL PARTS AND FEATURES 1. Power Button 2.1. Light ON/OFF Power ButtonButton ButtonButton 3.2.12.Power LCD Temperature Display Panel Light ON/OFF ON/OFF 4.3.13.Light Temperature UpButton Button LCD Temperature Display Panel Temperature Display Panel 5.4.14.LCD Temperature Down Button Temperature Up Button Up Button 6.5.15.Temperature Door Handle Down Temperature Button 16.Temperature Down Button 7.6. Cup Holder Door Handle Handle 8.7.17.
INSTALLATION GUIDE AND USER MANUAL ASSEMBLY INSTRUCTIONS INITIAL SETUP Remove exterior and interior packing materials and connect the wine and beverage cooler to power supply. Once it is plugged in, let it run for at least 30 minutes. Co not change the temperate or adjust any settings at this time. INSTALLATION OF YOUR APPLIANCE Use two or more people to move and install the appliance. Failure to do so can result in back or other injury.
INSTALLATION GUIDE AND USER MANUAL The appliance must be installed with all electrical, water and drain connections in accordance with state and local codes. Make certain that the pipes are not pinched, kinked or damaged during installation. Check for leaks after connection. Note: Designed for indoor, home use only. The appliance should not be locate next to sources of high heat or in direct sunlight. Do not store or install the appliance outdoors, in a garage, basement or in moist areas.
INSTALLATION GUIDE AND USER MANUAL HANDLE INSTALLATION Pull away the door gasket in the area where the handle is to be installed. The gasket is easily removed by hand, no tools are necessary. Insert the two (2) screws with the lock washers and flat washers through the gasket side of the door frame until the screws pass through the door frame. Follow the sequence shown in the figure. Align the handle with the screws installed in the above step.
INSTALLATION GUIDE AND USER MANUAL OPERATING INSTRUCTIONS Power Powers on/off the appliance. To turn off the appliance, touch the mark and hold 5 seconds. The light of the display panel will off if no operations for 20 seconds. Light To control the interior light to turn on/off. Up To increase the corresponding zone set temperature by 0.1 or 0.1 . Down To decrease the corresponding zone set temperature by 0.1 or 0.1 .
INSTALLATION GUIDE AND USER MANUAL Self-Error Detecting System Code Problem E1 Open circuit in the temperature sensor 1 E2 Short circuit in the temperature sensor 1 E3 Open circuit in the temperature sensor 2 E4 Short circuit in the temperature sensor 2 E8 Communication Failure E9 Communication Signal Overtime Waiting F0 Fault in the Relay of Compressor F1 Fault in the Fan (FIC) F2 Fault in the Fan (FIH) F3 Fault in the Fan (F2C) F4 Fault in the Fan (F2H) F5 Fault in the Relay of H
INSTALLATION GUIDE AND USER MANUAL SETTING THE TEMPERATURE The temperature can be set between 5 and 22 . The temperature will increase by 0.1 or 0.1 if you touch UP once; Or the temperature will decrease by 0.1 or 0.1 if you touch DOWN once. In order to adjust the temperature, you have to first unlock the control panel by press and hold and together for 5 seconds. The control panel is unlocked when the buzzer sounds twice.
INSTALLATION GUIDE AND USER MANUAL SHELVES To prevent damaging the door gasket, make sure to have the door completely opened when pulling the shelves out of the rail compartment. For easy access to the storage content, you must pull the shelf out of the rail compartment; however this unit was designed with a plastic post on each side of the shelf track to prevent bottles from falling. When removing the shelf out of the inner rail, make sure to remove all items first.
INSTALLATION GUIDE AND USER MANUAL Please Note: a. Do not use abrasive cleaners to clean the wine & beverage cooler. b. Use mild, soapy water to clean the unit’s door seal. c. To ensure efficient operation, also thoroughly clean the back and bottom of the wine and beverage cooler. TROUBLESHOOTING Problem The wine and beverage cooler does not cool. The wine and beverage cooler does not get cold enough. The wine and beverage cooler seems to make too much noise. Frost is building up in the unit.