Installation Instructions Complete set active Sound incl. Soundbooster Hyundai Santa Fe III v1.1 (23.05.2017) Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
Contents 1 Liability Exclusion 3 2 Copy Right 4 3 General Notes 4 4 Safety instructions 5 5 Requirements for the determinable operation 5 6 Note 5 7 How to connect a cable to another 6 8 Note Cable Inscription/Color 7 9 Assembly instructions 8 10 Removing coverings drivers side 9 11 Cable connections 10 12 Control unit connection / pushbutton installation 11 13 Removing trunk trim panel 12 14 Cable routing 13 15 Installation sound generator 14 16 Important Information Sound Boo
1 Liability Exclusion Dear Customer Our cable sets are developed according to the connection- and circuit diagrams of the corresponding car manufacturer. Before the original production the cable sets will be tested on an original car. Therefore, the integration into the car electronics will be executed according to the instructions of the manufacturer.
2 Copy Right Our installation- and removal instructions, installation plans, software and other documentation with texts or pictures are protected by copy right. A publication or distribution of these documents is only permitted with a written approval of Kufatec GmbH & Co. KG. 3 General Notes Regarding the development there has especially been paid attention to your personal safety together with the most possible operating comfort, modern design and actual product technologies.
4 Safety instructions The installation may only be executed by trained qualified personnel. Please execute the installations only in a condition of dead voltage. Here please separate for example the battery from the main power supply and consider the instructions of the car manufacturer. • In order to not endanger your own driving safety please never use security relevant screws, bolts or other fixation pieces at steering, brake system or other components.
7 How to connect a cable to another 1 2 3 4 5 6 Figure 1: How to connect a cable to another No. 1 2 3 4 5 6 Table 1: How to connect a cable to another Work step Take the cable of the vehicle, to which you want to connect, (green marked here) and strip the insulation at one point with a suitable tool (cable stripper/cutter knife). Now take the cable of the cable set, which you want to connect, (yellow marked here) and strip the insulation at the end. Twirl the wires of the stripped cable together.
8 Note Cable Inscription/Color Figure 2: Cable Inscription If our cable set consists exclusively of grey wires, connect the wires according to the cable inscription. Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
9 Assembly instructions The following illustration shows the cable routing as well as the position of the individual components. 2,3,4 1 1 2,3,4 Figure 3: Vehicle overview • 1 External sound generator incl. mounting plate • 2 Control unit for engine sound generation • 3 Sound Booster Pro (module) • 4 Pushbutton Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
10 Removing coverings drivers side 1 2 4 3 5 6 Figure 4: Removing coverings drivers side Nr. 1 2 3 4 5 6 Table 2: Removing coverings drivers side - instructions Work step Remove the lateral covering of the dashboard using a trim tool. Remove the covering of the fuse box. Remove the front door sill trim using a trim tool. Pull the bonnet release lever backwards and then sideways out. Remove the lower A-pillar cover using a trim tool. Remove the rear door sill trim using a trim tool.
11 Cable connections 2 1 4 3 4 Figure 5: Cable connections Nr. 1 2 3 4 Table 3: Cable connections - instructions Work step Remove the OBD-Plug by loosening the latch noses and pulling the plug out backwards. Connect the cables for CAN High & Low as follows: CAN High (black/white) to PIN 6 (green) CAN Low (black/yellow) to PIN 14 (orange) Connect the ground cable (brown) to the marked ground spot.
12 Control unit connection / pushbutton installation 3 1 2 3 Figure 6: Control unit connection / pushbutton installation Nr. 1 2 3 Table 4: Control unit connection / pushbutton installation - instructions Work step Connect the control unit to the cable set and attach it to the marked place. Connect our module to the cable set and attach it to the marked place. Drill a hole at the marked spot for the pushbutton and install it. Kufatec GmbH & Co. KG - Dahlienstr.
13 Removing trunk trim panel 2 1 3 4 5 Figure 7: Removing trunk trim panel Nr. 1 2 3 Table 5: Removing trunk trim panel - instructions Work step Open the storage compartment. Remove the three screw covers at the marked spots. Loosen the three screws at the marked spots. 4 5 Remove the rear cover and the styrofoam case. Loosen both screws of the side trim at the marked spots. Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
14 Cable routing 2 1 3 4 5 Figure 8: Cable routing Nr. 1 2 3 4 5 Table 6: Cable routing - instructions Work step Lay the connecting cable for the sound generator along the door sill trim to the B-pillar. Lay the connecting cable along the rear door sill trim and use a pull through aid to push it behind the side trim. Lay the cable along behind the side trim and pull it out at the marked spot. Remove the marked rubber grommet from the trunk floor.
15 Installation sound generator 1 1 2 3 Figure 9: Installation sound generator Table 7: Sound generator installation - instructions Nr. 1 Work step Loosen the screws at the marked spots on the underbody. 2 Attach the sound generator to the underbody with the screws from step 1. 3 Attach the delivered steel wire rope to the sound generator as well as to a suitable spot at the car. Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
16 Important Information Sound Booster Please use for the fixation of the Sound Booster suitable high tensile screws. In order to avoid losening of the screws by vibration please make the screws safe with appropriate factory material e.g Threadlock. Please additionally check the stability of the Sound Booster regularly and if necessary retighten the screws. In case of no consideration we do not assume liability for possible damages.
List of Figures 1 2 3 4 5 6 7 8 9 How to connect a cable to another . . . . . . . . Cable Inscription . . . . . . . . . . . . . . . . . . Vehicle overview . . . . . . . . . . . . . . . . . . Removing coverings drivers side . . . . . . . . . . Cable connections . . . . . . . . . . . . . . . . . Control unit connection / pushbutton installation Removing trunk trim panel . . . . . . . . . . . . Cable routing . . . . . . . . . . . . . . . . . . . . Installation sound generator . . . . . . . . . . . . . . . .
