Installation Instructions Complete set active Sound incl. Soundbooster VW T5 7H v1.0 (20.09.2016) Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
Contents 1 Liability Exclusion 3 2 Copy Right 4 3 General Notes 4 4 Safety instructions 5 5 Requirements for the determinable operation 5 6 Note 5 7 How to connect a cable to another 6 8 Note Cable Inscription/Color 7 9 Assembly Instructions 8 10 Removing trim panel driver’s side front 9 11 Connection CAN-High & CAN-Low / ground / ignition lead 11 12 Routing connecting cable sound generator 12 13 Installation sound generator 13 14 Software 14 15 Important Information Sound Booste
1 Liability Exclusion Dear Customer Our cable sets are developed according to the connection- and circuit diagrams of the corresponding car manufacturer. Before the original production the cable sets will be tested on an original car. Therefore, the integration into the car electronics will be executed according to the instructions of the manufacturer.
2 Copy Right Our installation- and removal instructions, installation plans, software and other documentation with texts or pictures are protected by copy right. A publication or distribution of these documents is only permitted with a written approval of Kufatec GmbH & Co. KG. 3 General Notes Regarding the development there has especially been paid attention to your personal safety together with the most possible operating comfort, modern design and actual product technologies.
4 Safety instructions The installation may only be executed by trained qualified personnel. Please execute the installations only in a condition of dead voltage. Here please separate for example the battery from the main power supply and consider the instructions of the car manufacturer. • In order to not endanger your own driving safety please never use security relevant screws, bolts or other fixation pieces at steering, brake system or other components.
7 How to connect a cable to another 1 2 3 4 5 6 Figure 1: How to connect a cable to another No. 1 2 3 4 5 6 Table 1: How to connect a cable to another Work step Take the cable of the vehicle, to which you want to connect, (green marked here) and strip the insulation at one point with a suitable tool (cable stripper/cutter knife). Now take the cable of the cable set, which you want to connect, (yellow marked here) and strip the insulation at the end. Twirl the wires of the stripped cable together.
8 Note Cable Inscription/Color Figure 2: Cable Inscription If our cable set consists exclusively of grey wires, connect the wires according to the cable inscription. Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
9 Assembly Instructions The following illustration shows the cable routing as well as the position of the individual components. 2,3,4 1 1 4 2,3 Figure 3: Vehicle overview • 1 External sound generator incl. bracket • 2 Control unit for engine sound generation • 3 Sound Booster Pro (module) • 4 Pushbutton Kufatec GmbH & Co. KG - Dahlienstr. 15 - 23795 Bad Segeberg - e-mail: info@kufatec.
10 Removing trim panel driver’s side front 1 1 3 2 4 3 Figure 4: Removing trim panel driver’s side front Nr. 1 2 3 4 Table 2: Removing trim panel driver’s side front - instructions Work step Loosen the two marked screws of the lower trim panel of the dashboard and take it out afterwards. Remove the lateral covering of the dashboard using a trim tool. Now loosen the three marked screws at the bottom of the front trim panel of the dashboard.
1 2 4 3 Figure 5: Removing trim panel driver’s side front Table 3: Removing trim panel driver’s side front - instructions Nr. 1 2 3 4 Work step Loosen the two marked screws behind the light switch and take the front trim panel of the dashboard out afterwards. Loosen the marked covering of the sill trim with a trim tool. Remove the marked plug and take the covering out completely afterwards. Remove the sill trim using a trim tool. Kufatec GmbH & Co. KG - Dahlienstr.
Connection CAN-High & CAN-Low / ground / ignition lead 1 1 2 2 3 4 Figure 6: Connection CAN-High & CAN-Low / ground / ignition lead Nr.
Routing connecting cable sound generator 1 2 3 2 3 3 Figure 7: Routing connecting cable sound generator Nr. 1 2 3 Table 5: Routing connecting cable sound generator - instructions Work step Route the connecting cable for the sound generator from the dashboard to the sill trim. Route the cable further from the sill trim beneath the driver’s seat with a pull through aid. Move the seat to the very front for this. Guide the connecting cable through the marked grommet under the seat to the underbody.
Installation sound generator 1 2 4 3 5 6 Figure 8: Installation sound generator Nr. 1 2 3 Table 6: Installation sound generator - instructions Work step Route the connecting cable for the sound generator along the tank. Guide the cable further behind the protection plate to the marked opening. Now loosen the left, marked screw of the bracket of the middle silencer. 4 Attach the sound generator with the just loosened screw.
Software 1 Figure 9: Software Nr. 1 Table 7: Notes for the software Work step For the commissioning, our Sound Booster Software for PC / Mac should be used. Step 1: Download the appropriate software via the following link: https://www. sound-booster.com. Step 2: Turn the ignition of the vehicle on and only then connect the PC / Mac with a USB cable with our module. It is important here to make sure previously that plus and minus are connected correctly.
2 1 3 Figure 10: Software Nr. 1 2 3 Table 8: Notes for the software Work step If no current vehicle is identified, you have to select the vehicle via the Manual Selection as follows: Open the dropdown-menu, search for your vehicle and select it. Click on Manual Selection to save the vehicle on the module permanently. If you don’t find your vehicle in this list, it is possibly necessary that the software has to be adapted to your vehicle. For this, please contact us via e-mail: info@kufatec.
15 Important Information Sound Booster Please use for the fixation of the Sound Booster suitable high tensile screws. In order to avoid losening of the screws by vibration please make the screws safe with appropriate factory material e.g Threadlock. Please additionally check the stability of the Sound Booster regularly and if necessary retighten the screws. In case of no consideration we do not assume liability for possible damages.
List of Figures 1 2 3 4 5 6 7 8 9 10 How to connect a cable to another . . . . . . . . . . . . . . . Cable Inscription . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle overview . . . . . . . . . . . . . . . . . . . . . . . . . Removing trim panel driver’s side front . . . . . . . . . . . . Removing trim panel driver’s side front . . . . . . . . . . . . Connection CAN-High & CAN-Low / ground / ignition lead Routing connecting cable sound generator . . . . . . . . . . .
