0” Cabinet Saw Sliding Table Owner’s Manual Model: 10-110B/E Record the serial number and date of purchase in your manual for future reference. Serial number: Date of purchase: For more information: www.rikontools.com or info@rikontools.com Part #10-110B/EM2 For Parts or Questions: techsupport@rikontools.
Operator Safety: Required Reading IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. There are certain applications for which this tool was designed. We strongly recommend that this tool not be modified and/or used for any other application other than that for which it was designed. If you have any questions about its application, do not use the tool until you have contacted us and we have advised you.
ALWAYS DISCONNECT TOOLS. Disconnect tools before servicing and when changing accessories such as blades, bits, and cutters. ALWAYS AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in cord. NEVER LEAVE TOOLS RUNNING UNATTENDED. ALWAYS CHECK FOR DAMAGED PARTS. Before initial or continual use of the tool, a guard or other part that is damaged should be checked to assure that it will operate properly and perform its intended function.
Table of Contents Safety Warnings........................................................................................................................................2 -3 Table Saw Safety Rules ..........................................................................................................................3 Specifications ........................................................................................................................................4 Contents of Package ..................
Content of Package Model 10-110B/E 10” Table Saw Sliding Table is shipped complete in 2 boxes. Unpacking and Checking Contents Separate all “loose parts” from packaging materials and check each item with “Table of Loose Parts” to make sure all items are accounted for, before discarding any packaging material.
TABLE OF LOOSE PARTS Item Part Name A Swing Arm Assembly B Swing Arm Extension Bar C Sliding Table Carriage D Sliding Table Support Arm E Loose Parts Bag Qty 1 1 1 1 1 Box #2 A B E C D 6
Getting To Know Your Sliding Table 1 3 2 4 5 9 8 7 6 1. Flip Stop 2. Miter Fence 3. Sliding Table 4. Sliding Table Locking Pin 5. Push Block 6. Slide Handle 7. Swing Arm Assembly 8. Carriage Table Support Arm 9.
Assembly Mounting the Swing Arm Bracket 1. Open the motor cover located at the left side of the saw. 2. With assistance hold the swing arm bracket against the saw body and attach using four 8MM hex bolts, four 8MM washers and four 8MM hex nuts. 3. Slide the four 8MM hex bolts through the bracket and saw body and attach using the four 8 washers and four 8MM hex nuts from inside the saw body. Figure 1. Figure 1 Installing the Swing Arm Extension Bar 1.
Assembly Mounting the Sliding Table Continued A 3. Slide the hardware toward the cast mounting bracket located on the saw body. Place the adjusting plate on top of the set screws as shown (A,Fig.5). 4. Tighten the lock knob slightly, leaving loose for adjustment. 5. Repeat procedure for rear mounting bracket. Figure 5 6. Adjusting the parallel of the saw table and sliding table with the four set screws (A, Fig.5). Installing the Sliding Table Carriage 1.
Assembly Carriage Table Support Arm Installation A 1. Insert the support arm into the swing arm extension bar as shown (A, Fig. 9) making sure that bearing assembly rests between the adjusting nuts and the swing arm extension bar (B, Fig. 9). B Reminder: Tighten the carriage bolts shown in Figure 8 on page nine once the support arm is installed. Figure 9 2. Hold the support arm in place by installing the second bearing set and adjusting nuts as shown.
Assembly Installing the Sliding Table Miter Fence 1. Locate the miter fence (A, Fig. 13) and miter fence locking knob (B, Fig. 13) as shown. B A Figure 13 2. Lay the miter fence on top of the sliding table carriage and place the rotation shaft into the hole on the sliding table carriage. Figure 14. Figure 14 3. Install the miter fence locking knob from the underneath of the sliding table carriage. Figure 15.
Assembly Installing the Sliding Table Locking Pin A 1. Locate the locking pin with the black handle and thread it through the sliding table body with wrench as shown. Figure 17. Figure 17 Adjustment Leveling the Sliding Table to the Saw NOTE: The sliding table should be set approximately 3/64” of an inch higher than the saw table to prevent sheet goods from binding against the table. A 1. Loosen the two sliding table lock knobs slightly. (B, Fig. 18) 2.
Adjustment Slide Table Clearance to Saw Blade 1. Place a square on the front edge of the sliding table. (A-Fig. 20) B A 2. Push the sliding table until the top of the square clears the back edge of the leading tooth on the saw blade. (B-Fig. 20) Figure 20 3. If the square does not clear the back edge of the leading tooth on the saw blade, loosen the two locking knobs under the slide table. Move the table support forward or backwards until the aligment is correct. (A-Fig.
Operation Cutting Sheet Goods 1. Adjust the hold down plate according to the width of material to be cut. 2. Lay the workpiece onto the table and up against the saw fence. 3. Slide the workpiece through the saw blade until the material engages the hold down plate. Walk the workpiece through the cut with the sliding table until the workpiece clears the saw blade and the cut is completed.
Rip Fence Installation Fence Bar Placement with Sliding Table With the sliding table installed the front and rear fence bars must be relocated. Align the notches in the fence bars with the right miter slot in the main table. (A-Fig. 26) Follow the fence installation instructions found on page nine of the 10-110/10-050 Cabinet Saw manual. A Figure 26 Maintenance Caution! BEFORE CLEANING OR CARRYING OUT MAINTENANCE WORK, DISCONNECT THE MACHINE FROM THE POWER SOURCE (WALL SOCKET).
Troubleshooting WARNING! FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING. For parts or technical questions contact: techsupport@rikontools.com or 877-884-5167.
Parts Diagram 17
Parts List Key No. 1E 2E 3E 4E 5E 6E 7E 8E 9E 10E 11E 12E 13E 14E 15E 16E 17E 18E 19E 20E 21E 22E 23E 24E 25E 26E 27E 28E 29E 30E 1F 2F 3F 4F 5F 6F 7F 8F 9F 10F 11F 12F Part No. Description Key No.
Warranty 2-Year Limited Warranty RIKON Power Tools/Richen Enterprise, Inc. (“Seller”) warrants to only the original retail consumer/purchaser of our products that each product be free from defects in materials and workmanship for a period of two (2) years from the date the product was purchased at retail. This warranty may not be transferred.
For more information: 110 Cummings Park Woburn, MA 01801 877-884-5167/781-933-8400 techsupport@rikontools.com www.rikontools.com Copyright Richen Enterprise, Inc.