DF PROFI II CPCI Installation Instructions V1.7 27.02.2017 Project No.: Doc-ID.
h:\dokumente\project\5302_df_profi_ii\anwenderdoku\installation\cpci\kunbus\version_1.6\df cpci_e.doc profi Revision History Version Date V1.7 V1.6 V1.5 V1.4 V1.3 V1.2 V1.1 V1.0 27.02.2017 30.07.2013 23.09.2009 09.09.2009 04.08.2009 08.01.2008 14.11.2006 13.08.
DF PROFI II CPCI - Installation Instructions Contents Contents 1 Installation of the Board ................................................................................................ 1 2 Safety Instructions ........................................................................................................ 2 3 Pin Assignment ............................................................................................................. 3 4 Description of the LEDs ............................
Contents DF PROFI II CPCI - Installation Instructions List of Figures Figure 1: DF PROFI II CPCI Board ........................................................................................ 1 Figure 2: PROFIBUS Terminator ........................................................................................... 3 Figure 3: Declaration of Conformity, page 1 ........................................................................... 6 Figure 4: Declaration of Conformity, page 2 ..........................
DF PROFI II CPCI - Installation Instructions 1 Installation of the Board Installation of the Board The DF PROFI II CPCI is a plug & play compatible board. The configuration entirely takes place by means of the delivered software or the BIOS of your PC respectively. Thus, no jumpers or DIP-switch adjustments are necessary. To mount the board, please proceed as follows: Please see also the operating instructions of your PC.
Safety Instructions 2 DF PROFI II CPCI - Installation Instructions Safety Instructions WARNING: Disregarding this warning may result in damage to equipment and/or serious personal injury. Only qualified personnel may start up and operate this device. According to the safety instructions in this text, qualified personnel are persons who are authorized to start up, to ground, and to mark devices, systems, and equipment according to the standards of safety technology.
DF PROFI II CPCI - Installation Instructions 3 Pin Assignment Pin Assignment Pin Number 1 3 5 6 8 Signal RxD/TxD-P 0V (potential free 80 mA) 5V (potential free 80 mA) RxD/TxD-N Function shielding Data+ Feeding of bus terminator Feeding of bus terminator Data- Direction Input/Output Input Output Input/Output Table 1: Pin Assignment Remark: To assure correct operation of the PROFIBUS, a terminating resistor must be mounted at each bus end (Purchase No.: 4000-7-002-H).
Description of the LEDs 4 DF PROFI II CPCI - Installation Instructions Description of the LEDs Green LED: On: Firmware loaded and started Off: Firmware not loaded Yellow LED: On: PROFIBUS started Off: PROFIBUS stopped Red LED: On: PROFIBUS failure (min. one slave not connected to the bus or with external diagnosis) Off: No PROFIBUS failure 4 V1.7 / 27.02.
DF PROFI II CPCI - Installation Instructions 5 Technical Data Technical Data Processor Net+Arm 40, 33 MHz PROFIBUS Controller ASPC2, 48 MHz Memory 1 Mbyte SRAM 2 Mbyte Flash Type Memory PCI Interfaces 32 Bit (supports both 5 V and 3.3 V) PROFIBUS Interfaces 1 * Sub-D 9 pins Interface Physics RS485 (isolated) PROFIBUS Data Rates 9600 Bit/s - 12000 KBit/s Data Size of Process Image max.
Declaration of Conformity 6 DF PROFI II CPCI - Installation Instructions Declaration of Conformity Figure 3: Declaration of Conformity, page 1 6 V1.7 / 27.02.
DF PROFI II CPCI - Installation Instructions Declaration of Conformity Figure 4: Declaration of Conformity, page 2 KUNBUS V1.7 / 27.02.
Declaration of Conformity DF PROFI II CPCI - Installation Instructions Figure 5: Declaration of Conformity, page 3 8 V1.7 / 27.02.
DF PROFI II CPCI - Installation Instructions Declaration of Conformity Final Page! KUNBUS V1.7 / 27.02.
