User's Manual
Table Of Contents
- Kurzweil International Contacts
- Table of Contents
- Introducing Forte SE
- Getting Started
- Features of the Forte SE
- Terminology
- The Operating Modes
- Program Mode
- Program Edit Mode
- About Program Edit Mode
- Differences Between Regular and Advanced User Type
- Selecting Parameters
- VAST and KB3 Programs
- VAST Program Structure
- Editing VAST Programs
- The Parameters (PARAMS) Page
- The Program FX (FX) Page
- The Layer FX (LYR_FX) Page
- The COMMON Page
- The KEYMAP Page
- The LAYER Page
- The PITCH Page
- The AMP Page
- The Algorithm (ALG) Page
- The DSP Control (DSPCTL) Page
- The DSP Modulation (DSPMOD) Page
- The OUTPUT Page
- The LFO Page
- The ASR Page
- The Function (FUN) Page
- The Amplitude Envelope (AMPENV) Page
- The Envelope 2 (ENV2) and Envelope 3 (ENV3) Pages
- The Envelope Control (ENVCTL) Page
- The Arpeggiator Function
- The Utility Soft Buttons, HELP Soft Button and Favorites Buttons Functions
- Editing VAST Programs With KVA Oscillators
- KB3 Program Structure
- Editing KB3 Programs
- KB3 Editor: The Parameters (PARAMS) Page
- KB3 Editor: The Program FX (FX) Page
- KB3 Editor: The COMMON Page
- KB3 Editor: The Tone Wheels (TONEWL) Page
- KB3 Editor: The Drawbars (DRAWBR) Page
- KB3 Editor: The PITCH Page
- KB3 Editor: The AMP Page
- KB3 Editor: The KEYCLICK Page
- KB3 Editor: The PERC1 Page
- KB3 Editor: The PERC2 Page
- KB3 Editor: The EQ Page
- KB3 Editor: The OUTPUT Page
- KB3 Editor: The LFO, ASR, FUN, and ARP Pages
- The Effects Chain Editor
- Keymap and Sample Editing
- Multi Mode
- Multi Edit Mode
- About Multi Edit Mode
- Selecting Parameters
- Zone Parameters
- OVERVIEW Page
- MAIN Page
- KEYVEL (KeyVelocity) Page
- BEND Page
- CCTLS (CCs/Continuous Controllers) Page
- SWITCH (Switches) Page
- Controlling Program Parameter Assignments from Multi Mode
- The Controller Destination List
- COMMON Page
- ARP1 and ARP2 (Arpeggiator 1 & 2) Pages
- FX Page
- AUXFX 1, AUXFX 2
- About Auxiliary Effects
- Audio Input (AUD-IN)
- The Utility Soft Buttons, HELP Soft Button and Favorites Buttons Functions
- Save User Multis
- Global Mode
- Song Mode and the Song Editor
- Getting Started with the Sequencer
- Song Mode: The MAIN Page
- Song Mode: The BIG Page
- Song Mode: The FX Pages
- Song Mode: The MIXER Page
- Song Mode: The METRONOME Page
- Song Mode: The Filter Pages (RECFLT and PLYFLT)
- Song Mode: The MISC Page
- Song Mode: The STATS Page
- The Song Editor
- Song Editor: The COMMON Page
- Song Editor: The TRACK Page
- Song Editor: Track Functions
- Song Editor: The EVENT Page
- System Mode
- Troubleshooting
- MIDI Implementation
- Physical Specifications
- Programs
- KB3 Programs
- Multis
- Effects Chains
- Index
Program Edit Mode
The Envelope Control (ENVCTL) Page
7-54
Adjust
is is the familiar Coarse adjust found on many other pages. Use it here to change the rate
of one of the envelope sections without reprogramming the envelope itself. is parameter
doesn’t give you realtime control over the envelope. It is, however, a good way to adjust
the natural envelopes without switching to a User envelope and trying to approximate the
Natural envelope.
Key Tracking
is uses the MIDI note number of each key as the control input for the current layer’s
corresponding envelope section. When the value of this parameter is greater than 1.000x,
notes above C 4 will make the envelope section run faster, while notes below C 4 will make it
run slower. When the value of this parameter is less than 1.000x, notes above C 4 will make
the envelope section run slower, and notes below C 4 will make it run faster. is gives you
realtime envelope control right from your MIDI controller. You might use it, for example, to
cause an acoustic guitar sound to decay quicker at the high end of the keyboard (set the key
tracking to a positive value).
Velocity Tracking
Use your attack velocity as the control input for the current layer’s attack section (this
parameter doesn’t apply to decay or release). When the value of this parameter is greater
than 1.000x, attack velocities greater than 64 make the attack section run faster, and attack
velocities below 64 make it run slower. is gives you realtime attack control over the
envelope.
Source, Depth
ese two parameters work together to let you assign a control like the Mod Wheel to aect
the current layer’s amplitude envelope in realtime. e value of the Source parameter denes
which control aects the envelope section, and the value of the Depth parameter denes how
much the rate is multiplied when the control is at its maximum value, 127. No eect is had
when the control is at its minimum value, 0, and Depth values are scaled for controller values
in between.