LTE MiFi wireless data terminal Use guide
Contents 1 PRODUCT INTRODUCTION................................................................................................................................... 1 1.1 1.2 1.3 2 PRODUCT INTRODUCTION.....................................................................................................................................1 TECHNICAL PARAMETERS......................................................................................................................................1 THE BASIC FUNCTION.
1 Product introduction 1.1 Product introduction Thank you for choosing LTE MiFi Wireless data terminal equipment. You can read the manual, to get a comprehensive understanding of the use of LTE MiFi, enjoy its perfect functions and simple operation.
2 Before use 2.1 Each part of the name and description 2.1.1 Check the packaging Parts The number 1 1 1 1 Wireless devices USB cable Quick use guide The battery 2.1.2 The appearance Power button: long press the power button to open/close the device. Display screen External memory card slot.
2.2.2 SIM card installed Install the SIM card, as shown below. 2.2.3 Install the battery Install the battery, as shown below. 2.3 Charging Use the power adapter to charge. Note: You must use the LTE MiFi original battery adapter, if you use the adapter provided by other manufacturers or agent, it may affect the use of the MiFi performance or dangerous, this behavior to violate the MiFi warranty terms and conditions as well as the state's rules on communications terminal products.
2.3.1.1 The iPhone connection instructions Enter into the Settings, click on the "Wireless LAN", the iPhones automatically brush Wi-Fi list, find LTE_XXXX, click “Connect”, then input password to connect. (LTE MiFi is encrypted by default, the default password is 12345678) 2.3.1.2 Android system connection instructions Into Settings/WLAN, open the WLAN, find the SSID, click “connect”, enter the password (different mobile phones may have different operating mode). 2.3.1.
After successfully log in , click “quick setting” to make settings of “user setting”,”Internet setting”, “Wireless setting”, then click “Finish” 2.3.2 Establish the network connection through USB This function is only for PC, process shows as below: PC drive installation Connect the device with PC via USB cable, power on the device. When the screen lit up, select “Install Marvell DIAG USB Device”to star the drive 2.3.
3 Interface setting operation This chapter describes only for administrator accounts log in. When Computers and equipment connect through Wi-Fi, input "http://192.168.0.1" in the browser's address bar, the default password is "admin", and click Log in button to log in WebUI.
WPA / WPA2 (most secure) -- Provides maximum level of security. Devices that support WPA or WPA2 will be able to join this network. You must enter a password between 8 and 63 characters. WEP (less secure) -- Provides security that is compatible with older devices. You must enter a password of exactly 5 or 13 characters. No Security (not recommended) -- Any wireless device can connect your network without entering a password. 3.
Enable or disable PIN, and change PIN. ThePIN Managment Screen contains the following fields: 3.2.4 PIN/PUK Attempts - display the number of PIN attempts and PUK attempts.
3.3.2 Connected Devices The Connected Devices screen displays a list of devices that are connected to the network. The Connected Devices screen also allows the user to block access to the Internet to a specific device. The Connection Devices screen contains the following fields: 3.3.
3.4.2 Wireless Security Settings The Wireless Security section allows users to define the network as well as the security parameters for the wireless home network as required. The factory default setting for security is WPA-WPA2 Mixed mode that allows only the WPA/WPA2 devices to associate with the home router. The Wireless Security section contains the following fields: Network Name -- Used to change the name of your wireless network.
3.5.2 Configuration Management Configuration Management Restore Factory Settings - This option resets the router to the factory defaults. Please note that the existing settings will be lost. 3.5.3 Software Upgrade The SW Upgrade screen is used to check for latest firmware versions and to update Marvell router router if a new version is available. Software Information The Software Information section provides information about currently used firmware version.
could result in battery leakage, overheating, cracking, fire or other malfunctions. Do not use your equipment near low signal or precision electronic equipment. Radio wave interference may cause the malfunctioning of such electronic equipment and other problems. Special attention must be paid near the following equipment: hearing aids, pacemakers and other electronic medical equipment, smoke detectors, automatic doors and other automatic control installations.
