EX10 User Guide The future of sound. Made perfectly clear. At KV2 Audio our vision is to constantly develop technologies that eliminate distortion and loss of information providing a true dynamic representation of the source. Our aim is to create audio products that absorb you, place you within the performance and deliver a listening experience beyond expectation.
CONTENTS INTRODUCTION 3 HOW TO USE THIS MANUAL 3 Icons used include: 3 Introducing the EX10 3 Electronics 3 Acoustic Components 4 Enclosure Design 4 APPLICATIONS 4 AC POWER 4 CHAPTER 1: AC POWER REQUIREMENTS 5 Voltage Requirements 5 The Power Connector 5 Current Requirements 5 AC Cable Color Coding 6 IIMPORTANT SAFETY INSTRUCTIONS 6 SAFETY SUMMARY 6 The EX10 Control Panel 7 Audio Input and Output 7 Chapter 2: AUDIO SIGNAL 7 Amplifiers and Acoustic Filters 7 LED Status
INTRODUCTION HOW TO USE THIS MANUAL Electronics As you read this manual, you’ll find figures and diagrams to help you understand and visualize what you’re reading. You’ll also find numerous icons that serve as cues to flag important information or warn you against improper or potentially harmful activities. Amplifier power, electronic crossovers, phase alignment, equalization, time correction and speaker protection are integrated into the EX10’s amplifier module.
INTRODUCTION Acoustic Components with a maximum amount of mounting flexibility. KV2 Audio has developed a revolutionary woofer technology called Trans-Coil™. The woofer has two coils, a standard voice coil assembly and a second coil placed directly on the neodymium magnetic circuit’s pole piece. This technology eliminates voice coil inductance resulting in a flat impedance response above the resonance point and achieves faster transient response through increased force and control of the moving mass.
CHAPTER 1: AC POWER REQUIREMENTS Voltage Requirements The EX10 operates safely and without audio discon tinuity if the AC voltage stays within the operating window of 100V-120V in 115V mode, 205V-240V in 230V mode and 225V-260V when working in 250V mode, at 50 or 60Hz. CAUTION: If the On LED does not illuminate or the system does not respond to audio input, remove AC power immediately. Verify that the voltage is within the proper range.
CHAPTER 1: AC POWER REQUIREMENTS AC Cable Color Coding If the colors referred to in the diagram don’t correspond to the terminals in your plug, use the following guidelines: Connect the blue wire to the terminal marked with a N or colored black. Connect the brown wire to the terminal marked with an L or colored red. Connect the green and yellow wire to the terminal marked with an E or colored green or green and yellow. into your outlet, consult an electrician for replacement of the obsolete outlet. 11.
CHAPTER 2: AUDIO SIGNAL The EX10 Control Panel The EX10 features an easy to use rear control panel featuring audio input and output, level control, LED status lights and a low pass filter that can be engaged when the loudspeaker is used as a stage monitoring device. 0 POWER ON/ LIMITER SIGNAL/ THERMAL – 6dB LEVEL + 6dB The audio source must be capable of producing a minimum of 20 dB volts (10 volts rms into 600 ohms) to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
CHAPTER 2: AUDIO SIGNAL operating level. This type of protection allows the phase response of the system to remain unchanged as the level is lowered. By not compressing or limiting peak signal, dynamics also remain unchanged. The control objective is to regulate the operating temperature of the transducers magnetic circuits log term. This ensures no impact on performance due to power compression and allows the components to retain their ability to reproduce high dynamics.
CHAPTER 3: ROTATING THE EX10 HORN The EX10 horn can be rotated ninety degrees in order to accommodate applications where the speaker will be used or installed horizontally. This can be accomplished by removing the front grill. Removing the horn, rotating and replacing the horn. 90 Replacing the front grille. EX10 USER GUIDE P.
APPENDIX A: EX10 SPECIFICATIONS AND DATA System Acoustic Perfomance Max SPL Long-term Max SPL Peak -3dB Response -10dB Response Crossover Point 126dB 129dB 65Hz - 20kHz 55Hz - 28kHz 1.6kHz High Frequency Section Acoustic Design High Horn Coverage Horizontal / Vertical Rotatable Horn Throat Exit Diameter / Diaphragm Size Diaphragm Material Magnet Type Horn Loaded 100° x 80° YES 1" / 1.
APPENDIX B: EX10 ACCESSORIES, DRAWING EX10 ACCESSORIES Heavy duty cover for EX10 part name: COVER EX10 part number: KVV 987 068 Top Hat Adapter for EX Brackets part name: Top Hat Adapter part number: KVV 987 090 - including connection bolts Heavy duty telescopic speaker pole for ES/EX series part name: KV2-H part number: KVV 987 130 - M20 Telescopic speaker pole for ES/EX series part name: KV2-L part number: KVV 987 041 Horizontal bracket for EX10 part name: EX10 Horizontal Bracket part number: KVV 987
The future of sound. Made perfectly clear. At KV2 Audio our vision is to constantly develop technologies that eliminate distortion and loss of information providing a true dynamic representation of the source. Our aim is to create audio products that absorb you, place you within the performance and deliver a listening experience beyond expectation. KV2 Audio, Nádražní 936, 399 01 Milevsko, Czech Republic Tel. +44(0)1423 816868 www.kv2audio.