-15 dB +10 dB -15 dB +10 dB 0 Our aim is to create audio products that absorb you, place you within the performance and deliver a listening experience beyond expectation. LIMITER ACTIVE -12 dB +12 dB -12 dB +12 dB -15 dB +15 dB 20Hz OFF ON +15 dB 0 HI 40Hz 0 HI - MID EQ 0 LOW - MID HI PASS 0 LOW -15 dB At KV2 Audio our vision is to constantly develop technologies that eliminate distortion and loss of information providing a true dynamic representation of the source.
Contents Introduction How to use this manual Icons used include Important safety instructions Introducing the SAC2 Dimensions 4 4 4 5 5 Getting Started Unpacking Rack mounting AC Power requirements Voltage requirements Connector wiring 6 6 6 6 6 Features Front Panel Rear Panel 7 9 Using the system Stereo Master EQ 2-Way Stereo Crossover 2-Way Stereo Crossover with mono Subwoofer 12 Block Diagram 13 SAC2 Specification 14 10 11 Warranty Your SAC2 is covered against defects in material and workman
Introduction How to use this manual As you read this manual, you’ll find figures and diagrams to help you understand and visualise what you’re reading. You’ll also find numerous icons that serve as cues to flag important information or warn you against improper or potentially harmful activities. Icons used include NOTE ! CAUTION “NOTE” identifies an important or useful piece of information relating to the topic under discussion.
012345672841 01234567819ÿ2 ÿ ÿ ÿ ÿ ÿ ÿ ÿÿ!ÿ" ÿ # "ÿ $" %"&& %ÿ# ' #ÿ("%ÿ ÿ) ÿ*+ ÿ # "ÿ , ÿ #ÿ $ , ÿ&" # - % ÿ ÿ) &&ÿ ÿ %#ÿ % .ÿ . / 0ÿ ÿ ÿ ÿ %, ÿ ÿ ÿ 1) .
Getting started Unpacking Unpack the SAC2 and check to see if there is any damage to it. If you find any damage notify your supplier immediately. Only the consignee may institute a claim with the carrier for any damage incurred during shipping. Be sure to save the carton and all packaging materials for the carrier’s inspection.
Features Front Panel GAIN LIMITER LOW LOW - MID HI - MID HI 0 0 0 0 0 0 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.
Features Front Panel GAIN LIMITER LOW LOW - MID HI - MID HI 0 0 0 0 0 0 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 1.3k 45 Hz 1.6k 200 140 80 52 300 450 500 800 LOW-L LOW-R 1.3k 45 Hz 1.
Features Rear Panel POWER L HI OUTPUT R L / MONO R / MONO LOW OUTPUT INPUT L R WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE PHASE THIS PANEL OR ANY ATTACHED COMPONENTS. NO OPERATOR SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. SERIAL NUMBER 230 VAC, 50/60 Hz MAX 30WATTS WWW.KV2AUDIO.
Using the System Stereo Master EQ One of the advantages of the SAC2 is the ability to use the Notch Filters and four-band EQ as both a Master and Monitor/Fill EQ. The Low Output can be used to send a full-range PA signal by switching it to DIRECT mode. The Hi Output can be used to send a full-range signal by switching it to DIRECT mode or as a High Pass Filter with selectable 70Hz or 120Hz frequency to send signal to Monitor/Fill loudspeakers.
Using the System 2-Way Stereo Crossover The primary function of the SAC2 is as a 2-way stereo crossover. The Low Output is used as a stereo low pass signal for subwoofers. The Low Output should be switched to LPF and the Left and Right outputs sent to the subwoofers. The Hi Output is used as a stereo high pass signal for mid/hi loudspeakers. The Hi Output should be switched to HPF and the Left and Right outputs sent to the mid/hi loudspeakers.
Using the System 2-Way stereo crossover with mono subwoofer The SAC2 can also be used as a stereo crossover with a mono subwoofer. The Low Output is used as a mono low pass signal for a subwoofer. The Low Output should be switched to LPF and the Sub Mode switched to MONO. Either Low Output can be sent to the Subwoofer as the Low Outputs now play the same signal. The Hi Output is used as a stereo high pass signal for mid/hi loudspeakers.
70 Hz 120 Hz 70 Hz LOW PASS FITER CHANNEL-R - LF OUT LIMITER 120 Hz LIM-T L/R MONO DIRECT LPF X OVER HPF DIRECT FAST SLOW LOW OUTPUT HIGH OUTPUT HIGH PASS ON OFF CHANNEL- L - LF OUT SUB EQ 20 Hz LOW LOW HIGH EQ LINE DRIVER ON OFF LOW OUT LINE DRIVER METER -13 dB -8 dB -3 dB 0 dB +3 dB -13 dB -8 dB -3 dB 0 dB +3 dB HI OUT METER HMID LMID LOW-MID 40 Hz HI-MID EQUALIZATION HI HIGH PASS FITER STANDBY MUTE OFF PHASE PHASE -6 dB -12 dB NOTCH FILTERS FREQ 1 A
SAC2 Specification Connection Inputs Inputs type Input Impedance Max. Input level 2 Female XLR 20kΩ (balanced) +22dBu Outputs Outputs type Output Impedance Max.
The future of sound. Made perfectly clear. At KV2 Audio our vision is to constantly develop technologies that eliminate distortion and loss of information providing a true dynamic representation of the source. Our aim is to create audio products that absorb you, place you within the performance and deliver a listening experience beyond expectation. KV2 Audio, Nádražní 936, 399 01 Milevsko, Czech Republic T +44(0)1423 816868 F +44(0)1423 816869 www.kv2audio.