® OPERATOR’S MANUAL KM16BR KM16 SR12
KM16BR, KM16 SR12 TABLE OF CONTENTS Use of this manual............................................................................................2 Safety Guidelines......................................................................................... 2-3 Warranty and Service................................................................................... 4-5 Specifications............................................................................................... 6-7 Contents .....................
USE OF THIS MANUAL Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all of the chapters. It’s important that the operator know the principles of gun handling safety and operation prior to firing the Airsoft gun. SAFETY GUIDELINES ! WARNING! Failure to follow safety guidelines may result in serious injury. Safety Distance The effective shooting range is approximately 175 feet.
KM16BR, KM16 SR12 SAFETY GUIDELINES Identify Your Target and Backstop Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces where BBs are likely to ricochet in unpredictable directions. ! WARNING! Adult supervision is required for any person under the age of 18. Failure To Fire If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel.
WARRANTY AND SERVICE KWA Performance Industries, Inc. is committed to serve our customers with the finest quality products, the highest level of service, and customer satisfaction. Because of this, we offer a 45-day warranty on all KWA products we import and distribute. What is Covered Except as specified below, this warranty covers all defects in material and workmanship in KWA products occurring during the above warranty periods.
KM16BR, KM16 SR12 NOTE: THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE PACKAGE. PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE REFUSED AND RETURNED TO SENDER. NO EXCEPTIONS. This Warranty is Only Valid in the United States If your product does not require service, but you have questions regarding its operation, please contact our Technical Services Department as listed below.
SPECIFICATIONS KM16BR • Overall Length [Fixed] = 100.33 cm (39.5”) • Outer Barrel Length = 515 mm (20.27”) • Inner Barrel Length = 509 mm • Inner Barrel Diameter = 6.05 mm • Weight = 3.21 kg (7.7 lbs) • Barrel thread = 14 mm Negative • Caliber = 6 mm • Magazine Capacity = 350 • Rate of Fire = 20+ RPS • Velocity = 118~125 MPS (390~410 FPS) • Energy Output with .20g BB = 1.49 Joules • Power Source = 9.6v NiMh, 7.4v or 11.
KM16BR, KM16 SR12 SPECIFICATIONS KM16 SR12 • Overall Length [Fixed] = 100.33 cm (39.5”) • Outer Barrel Length = 515 mm (20.27”) • Inner Barrel Length = 509 mm • Inner Barrel Diameter = 6.05 mm • Weight = 3.21 kg (7.7 lbs) • Barrel thread = 14 mm Negative • Caliber = 6 mm • Magazine Capacity = 350 • Rate of Fire = 20+ RPS • Velocity = 118~125 MPS (390~410 FPS) • Energy Output with .20g BB = 1.49 Joules • Power Source = 9.6v NiMh, 7.4v or 11.
PACKAGE CONTENTS 1 KM16BR / KM16 SR12 Airsoft gun 2 Allen Wrenches (For cap screw removal) 1 Safety Cap 1 Sight Adjustment Tool 1 Cleaning Rod 1 Owners Manual 1 Removeable Sling Mount BREAK–IN PERIOD Airsoft guns, like many other products require a “break-in” period to ensure the optimal performance. This break-in period allows the spring, piston, gears and other moving parts to be seated and become more consistent in their movements.
KM16BR, KM16 SR12 LOADING HIGH CAP Magazine 1. Release the magazine by pressing the magazine release button. 2. Open the magazine top plate and pour the Airsoft BBs into the chamber. Close the plate when the chamber is full. 3. Turn the winding wheel on the bottom of the magazine to tighten the spring tension. This will allow the Airsoft BBs to feed through the top of the magazine. 4. Insert the magazine into the Airsoft gun until it clicks into place.
FIRE SELECTOR SWITCH 1. Safe In Safe mode the gun will not fire. For safety reason, you should keep the switch in Safe mode at all times when you are not ready to fire. SEMI SAFE 2. Semi-Auto In Semi-Auto mode the gun will fire one shot for each time you pull the trigger. SEMI 3. Full Auto In this Full Auto mode the gun will fire continuously as long as the trigger is depressed. ! AUTO SAFE SEMI SAFE AUTO WARNING: Do not pull the trigger when switching the fire selector.
KM16BR, KM16 SR12 BATTERY INSTALLATION 1. Set the fire selector switch to safe mode. Push down on the stock trap door release button to open the stock. Pull out the connector wire from inside the stock. 2. Place the battery into the stock. 3. Push the connector plugs together firmly until they click into place. 4. Push the wires into the stock and close the stock trap door.
HOP–UP SYSTEM The Hop-Up device is one of KWA’s standard features, giving Airsoft BBs greater stability, further travel and increased accuracy. Airsoft BBs are light-weight and can be affected by wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted according to the shooting environment or surroundings. HOP-UP ADJUSTMENT • Pull the charging handle to the rear, the ejection port will open and Hop-Up adjustment dial is revealed.
KM16BR, KM16 SR12 FRONT SIGHT ADJUSTMENT • The front sight can be moved up and down when zeroing rear sight Sight Adjustment Tool • Turn counter clockwise to lower the point of Impact • Stop turning when a click sound is heard Front Sight REAR SIGHT ADJUSTMENT • Flip the rear sight between general and precise aiming • To adjust the horizontal point of impact, rotate the windage knob located on the rear of the sight • To adjust the vertical point of impact, rotate the sight elevation knob located on th
DISASSEMBLY Note: Before opening the receiver, the piston must be in forward position. 1. Fire in semi-automatic mode 2-3 times to clear the barrel and reset piston. 2. Remove the Rear Pin only from lower receiver with the provided Allen wrenches. 3. Use 1 wrench to hold cap screw, the other to turn set pin. 4. After the removal of cap screw, use allen wrench to push pin out. 5. Pull the Upper receiver up. 6. Slide out the inner barrel with Hop-Up assembly.
KM16BR, KM16 SR12 Cleaning and Lubrication ! WARNING! Unload and clear the Airsoft gun of all BBs before cleaning. Cleaning Procedure The Airsoft gun barrel should be cleaned and lubricated after each shooting session. Regular cleaning prevents the effects of BB residue buildup, and ensures all parts are lubricated properly. 1. Ensure that the safety is engaged 2. Disable Hop-Up by dialing to the normal position 3. Remove the magazine and clear the chamber of loaded BBs 4.
BASIC TROUBLESHOOTING GUIDE FOR RIFLE SYMPTOMS CAUSE SOLUTIONS Selector set to Safe Mode Select Semi-Auto or Full-Auto Mode Dead battery Replace or Charge battery Burned out fuse Replace with a new fuse Motor damaged or bad connection Return gun for professional care Pinched wiring Return gun for professional care Motor is running but not firing Internal failure Return gun for professional care Motor or Battery is hot after short use Pinched wiring Return gun for professional care Motor d
KM16BR, KM16 SR12 Operating Under Unusual Conditions Unusual conditions are defined as any condition requiring special maintenance. Perform maintenance outlined for the climate similar to your operational area Extreme Cold: Operating an Airsoft gas gun in extremely cold temperatures is not recommended. Cold temperature will cause the Hop-Up Bucking to harden, reducing its effectiveness or cause the gearbox shell to fracture during operation, rendering the gun inoperable.
KM16BR DIAGRAM 49 114 269 316 289 267 241 165 300 241 244 241 552 547 554 554 242 128 19 176 126 69 193 68 16 175 171 36A 265A 162 203 266 203 161A 88 25 243 226 13 5 106 203 125 243 234A 101 15 159 35A 127 158 14 7 2 1A 204 163 229 47 48 164 18
KM16BR, KM16 SR12 KM16BR DIAGRAM 244 210 120 3 37 198 46 138 554 173 67 205 8 17 66 138 123 77 182 121 24 6 218 209 185 135 9 174 236 85 253 227 227 109 57 206 206 115 KM16BR PARTS LIST 243 13 Parts # Description Parts # Description Parts # Description 199-1002-1A Forward Assist Button 199-1002-19 Ejection Port Cover Lock Plunger 199-1002-68 Ejection Port Cover 199-1002-24 Selector Plate 199-1002-69 Ejection Port Cover Lock 199-1002-M70 Switch (Assembly) 1
KM16BR PARTS LIST Parts # Description Parts # Description Parts # 199-1002-121 Take Down Pin (Rear) 199-1002-123 Gear Box Set Pin 199-1002-125 199-1002-218 Screw M3X8 SC X 2 199-1002-291 Windage Knob Plunger 199-1002-226 Hop-Up Wheel Screw 199-1002-292 Hop Up Bar Pin 199-1002-227 Grip Screws X 2 Rear Sight Windage Screw 199-1002-126 Inner Barrel 199-1002-229 199-1002-127 Weaver Rail Pin Charging Handle Latch Pins X 2 199-1002-231 Gas Tube Pin 199-1002-128 Ejection Port Cover Pi
KM16BR, KM16 SR12 KM16 SR12 DIAGRAM 49 114 231 540 165 241 548 552 547 37 138 537 17 554 541 538 535 282 293 242 193 296 229 153 262 202 126 69 295 137 553 19 176 294 301 218 273 290 68 201 175 162 203 266 203 15 161A 88 203 25 125 5 106 7 2 1A 204 163 229 47 48 21 158 14 243 234A 101 16 159 35A 127 261 171 36A 265A 215 291 553 77 274 292 553 260 302 553 128 66 554 259 539 541 164 243 226 13
210 120 3 37 198 46 138 173 67 205 8 17 54 66 138 123 77 182 121 6 218 24 185 209 135 9 236 174 85 253 227 227 109 57 206 206 2 115 1 KM16 SR12 PARTS LIST 226 Parts # Description Parts # 199-1002-1A Foward Assist Button 199-1002-2 Inner Barrel Retainer 199-1002-3 BB Ramp 199-1002-5 Chamber Block 199-1002-6 Detente 199-1002-7 Bolt Plate Carrier 199-1002-8 Selector Cover 199-1002-9 Grip 199-1002-13 Hop-Up Adjustment Wheel 199-1002-14 199-1002-15 Descript
KM16BR, KM16 SR12 KM16 SR12 PARTS LIST Parts # Description Parts # Description Parts # Description 199-1002-292 Rear Sight Windage Screw 199-1002-293 Elevation Bar 199-1002-294 Elevation Dial Plunger 199-1002-123 Gear Box Set Pin 199-1002-204 Bolt Plate Carrier Screw 199-1002-125 Hop-Up Bar Pin 199-1002-205 Magazine Catch Screw 199-1002-126 Inner Barrel 199-1002-206 199-1002-127 Weaver Rail Pin Motor Plate Screw X 2 “Metric” 199-1002-207 Front Sight Clamp 199-1002-295 Rear Sigh
GEARBOX DIAGRAM AND PARTS LIST M124 M74 M51 M123 M3 M32 M37 M96 M42 M115 M33 M7 M71 M54 M55 M119 M70 M58 M62 M80 M38 M127-1 M127-1 M78 M64 M115 M121 M118 M116 M48 M120 M65 M115 M121 M116 M127 M114 M43 M19 M122 M36 M69 M117 M121 M63 M56 M119 M115 M121 M117 M107 M79 M53 M125 M120 M101 M125 M125 M125 M52 M59 M57 M40 M125 M97 M47 M127-1 M127 M125 M23 M127-1 M35 M39 M72 Parts # Description Parts # Description Parts # 199-1002-M3 199-1002-M7 199-1002-M19 Cylnder
KM16BR, KM16 SR12 MAGAZINE DIAGRAM AND PARTS LIST 25 Parts # Description Parts # Description 199-1002-MG300 Magazine Case 199-1002-MG314 Magazine Base Plate 199-1002-MG301 Inner Magazine Housing (Left) 199-1002-MG316 Sprocket Shaft 199-1002-MG302 Inner Magazine Housing (Right) 199-1002-MG317 Sprocket Wheel Pin 199-1002-MG303 BB Stop 199-1002-MG319 BB Stop Spring 199-1002-MG304 BB Compartment Cover 199-1002-MG320 Coil Spring 199-1002-MG305 Gear # 1 199-1002-MG321 Counter Weight
MMD14_KM16 V02 R2011.08.01 KWA Performance Industries, Inc. 18571 E. Gale Ave City of Industry, CA 91748 T: 626.581.1777 • F: 626.581.0777 www.kwausa.com Copyright © August, 2008 KWA Performance Industries, Inc. All Rights Reserved.
