Installation Sheet

2 / 4
MMMYYWWSSSSSSS
12345
WWWWWWWW
W
MMMYYWWSSSSSSS
12345
WWWWWWWWW
Green: Door
handing was
successful.
Proceed to
next step.
Red: Door
handing was
unsuccessful. Make
sure the lock interior and batteries are
correctly installed. Perform step 5B again.
If the door handing process is still unsuccessful
after a second attempt, see the Manual
Door Handing section on page 4.
NOTE: The lock will auto-hand again
after the irst time the door is locked or
unlocked using the keypad or app. This
is to conirm the door orientation.
Status
LED
If the bolt does not move, make sure
the batteries are correctly installed,
and perform step 5B again.
Note: The latch bolt will
only retract half way.
68272
21/8"
54 mm
11/2"
38 mm
actual size
For Lock
Bag
(2x)
What is the diameter of the hole in the door? Install the exterior keypad and mounting plate.
A C
Diameter is 21/8"
(54 mm)
Diameter is 11/2"
(38 mm)
or
Adaptor ring and frost guard
68780 are pre-assembled and
no changes are needed
Proceed to next step.
Remove pre-assembled adaptor
ring and frost guard 68780.
11/2" (38 mm) frost guard is
not included. If needed, please
contact Kwikset to order.
The cable goes
underneath the latch.
Support the exterior
assembly during mounting
plate installation.
Route the cable
through the center
hole, then push it into
the bottom hole.
adaptor
ring
Insert the key and
test the latch. If
the latch does not
extend or retract
smoothly,
adjust
the screws.
Remove the key
when inished,
and make sure
the latch bolt is
fully extended.
Keep parallel to the
edge of the door.
Make sure the torque blade is
centered in the mounting plate hole.
torque
blade
Tighten screws
evenly. DO NOT
over tighten screws.
a
c
b
d
Remove the mounting plate from the interior assembly.
B
68272
(2x)
3
Install the exterior keypad
68780
69316
Install 4 AA batteries in
the battery pack.
With the door open,
install the battery pack to
initiate auto-handing.
The latch will retract and extend to
learn the orientation of the door.
The Status LED will indicate success or failure.
A B C
D
Ensure correct polarity.
For best results, use
new, non-rechargeable
Alkaline batteries only.
MMMYYWWSSSSSSS
12345
W
WWWWWWW
W
69316
(2x)
(For
Lock Bag)
Ensure the turnpiece shaft is pointing up, and remove the interior cover and
battery pack from the interior assembly.
Install the interior assembly onto the mounting plate.
A B
a
c
b
d
If the turnpiece shaft
is pointing down,
place the cover back
onto the interior
assembly and rotate
the turnpiece until
you hear it click.
You may need to
apply some force.
Once the turnpiece
shaft is correctly
oriented, remove
the cover again.
Make sure turn
piece shaft is
rotated as shown.
Do not install
batteries
until step 5.
Ensure tight cable
connection.
Lay the excess cable
lat inside the bottom of
the interior housing.
align
a
c
b
d
bottom
hole
If turnpiece shaft is not oriented
correctly, put the cover back on and
rotate the turnpiece as shown in step C.
Remove the interior
cover from the
interior assembly.
Incorrect:
Ensure you are using the correct
screws. Using incorrect screws
will damage the product.
actual size
For Lock
Bag
(2x)
4
Install the interior assembly
5
Install the batteries and perform the door handing process
This step will teach your lock the orientation of your door and is crucial to lock operation.
Note: the
remaining three
screws will be
used in Step 9.