Installation Sheet

3 / 4
For Lock
Bag
69316
actual size
(3x)
68611
actual size
(1x)
69316 (3x)
(For Lock Bag)
When the window
is locked, you will
need to remove
the entire interior
cover and screws to
access the battery
pack and buttons.
For additional security,
you may choose to lock
the window by installing
the security screw.
The window on
the interior cover
is unlocked by
default for easier
access to the
battery pack
and buttons.
Important Information about the interior cover
Cover Installation Battery Pack Access
Install cover.
Note: You may
need to rotate
the turn piece
to align with the
turn piece shaft.
turn
piece
turn
piece shaft
Install screws.
a
b
If the window is
unlocked, slide
up the window
to access the
battery pack
and buttons.
window
68611 (1x)
(For Lock Bag)
If the window
is locked,
remove the
interior cover
and screws
to access the
battery pack
and buttons.
9
Install the interior cover
With the door open, insert the key to
extend the latch. Ensure that the latch
extends smoothly.
Initiate the process to add the lock
to your system at your smart home
controller. Refer to your smart
home system instructions for more
information.
Turn the key 180° to retract the latch.
Ensure that the latch
retracts smoothly.
If prompted by your smart home
system to add the lock, press button
“A” on the lock interior one time.
The red LED will illuminate when
the lock enters Add Mode.
Close the door. Insert and rotate
the key to lock the door. Ensure
that the door locks smoothly.
At this time, you may be prompted
by your smart home system to
enter the 5-digit PIN found on
the label of the interior assembly.
If not, proceed to step D.
Turn the key 180° to retract the latch.
Ensure that the door
unlocks smoothly.
If successful, re-name the lock
in your system (if applicable).
If unsuccessful, follow your
system’s instructions to remove
the lock from the controller and
any other network, then press
button “A” on the lock one time.
Perform steps AC again.
If still unsuccessful, consult
the Programming and
Troubleshooting Guide on
the Home Connect 620 page
at kwikset.com/support.
A
A
B
B
C
C
D
D
MMMYYWWSSSSSSS
12345
WWWWWWWWW
MMMYYWWSSSSSSS
12345
WWWWWWWWW
If your door does not lock and unlock smoothly, make sure you replaced your previous latch and strike with those supplied
in the box. If you still experience locking errors, complete the troubleshooting steps at http://bit.ly/HC620jam
or call Kwikset Support: 18668636584
SmartStart Enabled Products
SmartStart enabled
products can be added
into a Z-Wave network
by scanning the Z-Wave
QR Code present on the
product with a controller
providing SmartStart
inclusion. No further
action is required and the
SmartStart product will
be added automatically
within 10 minutes of being
switched on in the
network vicinity.
MMMYYWWSSSSSSS
12345
WWWWWWWWW
Button “A”
3x1x
Mastercode
For enhanced security, a
mastercode may be used when
adding/deleting user codes and
adjusting lock coniguration
settings. For more information
about the mastercode,
download the Programming
and Troubleshooting Guide on
the Home Connect 620 page
at kwikset.com/support.
GREEN with ONE BEEP RED with THREE BEEPS
or
Make sure the door is open.
Press the "Program" button once.
Enter user code. A total of 250 user
codes may be programmed.
Press button once.
A B C
What lights and sounds does the lock produce?
D
Programming was successful.
Programming was unsuccessful.
Ensure the user code is not a duplicate, is
between 4 and 8 digits, and the irst 4 digits
are not the same as another code.
Ensure the lock has room for an additional
code. If all user code positions are illed,
delete a code to make room for the new code.
It is recommended that you add and
delete all user codes through your
smart home control system. If your
system does not allow this, codes may
be added directly to the lock as shown
here.
Programming Timeout
During programming, if no button is
pressed for ive seconds, the system
will time out (indicated by three beeps
and a red lashing Kwikset button), and
you will need to restart the procedure.
MMMYYWWSSSSSSS
12345
WWWWWWWWW
redgreen
PIN: 12345
5-digit PIN
Ensure the user
code is not a
duplicate, is
between 4 and
8 digits, and the
irst 4 digits are
not the same as
another code.
8
6
7
Test the lock and check door alignment
Add the lock to your smart home system
Add user codes (250 max)
QR code
Ensure you are using the correct
screws. Using incorrect screws
will damage the product.
Ensure you are using the
correct screws. Using
incorrect screws will
damage the product.