User Guide

ManualsBrandsKymco ManualsOtherMO BW 50

14. REAR BRAKE/REAR FORK/REAR

WHEEL/REAR SHOCK ABSORBER

14-0

BET & WIN 50

__________________________________________________________________________________

REAR BRAKE/REAR BRAKE DRUN/

REAR SHOCK ABSORBER

__________________________________________________________________________________

SERVICE INFORMATION -------------------------------------------- 14-1

TROUBLESHOOTING ------------------------------------------------- 14-1

REAR WHEEL ---------------------------------------------------------- 14-2

REAR BRAKE DRUM -------------------------------------------------- 14-3

REAR SHOCK ABSORBER-------------------------------------------- 14-5

Summary of content (8 pages)

PAGE 1
4.
PAGE 2
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER BET & WIN 50 SERVICE INFORMATION GENERAL INSTRUCTIONS • When performing the services stated in this section, the engine and exhaust muffler must be cold to avoid scalding. • During servicing, keep oil or grease off the brake pads and brake disk. SPECIFICATIONS Item Rear wheel rim runout Rear shock absorber spring free length Rear brake drum I.D. Rear brake disk/ lining thickness Rear brake disk runout Rear brake master cylinder I.D.
PAGE 3
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER BET & WIN 50 REAR WHEEL REMOVAL Remove the exhaust muffler. (2-6) Remove the rear axle nut to remove the rear wheel. Rear Axle Nut INSPECTION Measure the rear wheel rim runout. Service Limits: Radial: 2.0mm replace if over Axial: 2.0mm replace if over INSTALLATION Install the rear wheel and apply SAE30# engine oil to the axle threads. Then, tighten the rear axle nut. Torque values: Rear axle nut: 107.8_ 127.
PAGE 4
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER BET & WIN 50 REAR BRAKE DRUM Remove the rear wheel. (14-3) Inspect the rear brake drum. Measure the rear brake drum I.D. Service Limit: 95.5mm replace if over BRAKE LINING INSPECTION Measure the brake lining thickness. Service Limit: 2.0mm replace if below °ØKeep oil or grease off the brake linings. REAR BRAKE DISASSEMBLY Remove the rear brake adjusting nut and disconnect the rear brake cable. Remove the rear brake shoes.
PAGE 5
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER Remove the brake arm bolt to remove the brake arm, wear indicator plate and felt seal. Remove the brake cam. Brake Arm Bolt Brake Arm BET & WIN 50 Wear Indicator Plate Brake Cam REAR BRAKE ASSEMBLY Apply grease to the anchor pin and brake shoe moving parts. Apply grease to the brake cam and install it. Grease Apply engine oil to the felt seal and install it to the brake cam. Install the wear indicator plate.
PAGE 6
14. REAR BRAKE/REAR FORK/REAR BET & WIN 50 WHEEL/REAR SHOCK ABSORBER Install the brake arm pin. Connect the brake cable and install the adjusting nut. Install the rear wheel. Adjust the rear brake lever free play. (3-12) Brake Arm Brake Cable Brake Arm Pin Adjusting Nut REAR SHOCK ABSORBER Air Cleaner REMOVAL Remove the rear carrier and frame body cover. (2-2) Remove the met-in box. (2-2) Remove the two air cleaner bolts. Bolts Remove the rear shock absorber upper mount bolt.
PAGE 7
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER BET & WIN 50 DISASSEMBLY Disassemble the left rear shock absorbers using the rear shock absorber remover. Rear Shock Absorber Remover INSPECTION Inspect the damper rod for bending or damage. Inspect the damper for oil leaks. Inspect the damper rubber for deterioration or damage. Damper Damper Rod Rubber Measure the front shock absorber spring free length.
PAGE 8
14. REAR BRAKE/REAR FORK/REAR WHEEL/REAR SHOCK ABSORBER ASSEMBLY Assemble the rear shock absorbers in the reverse order of disassembly. INSTALLATION Install the rear shock absorbers in the reverse order of removal. Torque: Upper Mount Bolt: 39.2N-m Lower Mount Bolt: 19.6_ 29.