User Guide

ManualsBrandsKymco ManualsOtherMO BW250

1. GENERAL INFORMATION

1-0

Bet & Win 2 50

__________________________________________________________________________________

GENERAL INFORMATION

__________________________________________________________________________________

ENGINE SERIAL NUMBER--------------------------------------------- 1-1

SPECIFICATION---------------------------------------------------------- 1-2

SERVICE PRECAUTIONS----------------------------------------------- 1-3

TORQUE VALUES ------------------------------------------------------- 1-7

TOOLS --------------------------------------------------------------------- 1-8

LUBRICATION POINTS------------------------------------------------- 1-9

CABLE & HARNESS ROUTING-----------------------------------------1-11

WIRING DIAGRAM-------------------------------------------------------------------1-16

TROUBLESHOOTING --------------------------------------------------1-17

Summary of content (28 pages)

PAGE 1
. GENERAL INFORMATION Bet & Win 250 1 1 __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ GENERAL INFORMATION ___________________________
PAGE 2
1.
PAGE 3
1. GENERAL INFORMATION Bet & Win 250 Cooling Type SPECIFICATIONS Displacement Fuel Used 1° 0.1 0.1 1450±50rpm Forced pressure & wet sump Inner/outer rotor type Full-flow filtration 1.1 liters Spark plug gap Battery Capacity Clutch Type NGK DPR7EA-9 0.9mm 12V10AH Dry multi-disc clutch Type Non-stage transmission Operation Automatic centrifugal Type Reduction Gear 13.82/7000 21.75/5500 8° 42° 33° Spark plug Transmission Gear 16.
PAGE 4
1. GENERAL INFORMATION SERVICE PRECAUTIONS n Make sure to install new gaskets, O-rings, circlips, cotter pins, etc. when reassembling. Bet & Win 250 n Apply or add designated greases and lubricants to the specified lubrication points. n After reassembly, check all parts for proper tightening and operation. n When tightening bolts or nuts, begin with larger-diameter to smaller ones at several times, and tighten to the specified torque diagonally.
PAGE 5
1. GENERAL INFORMATION n If the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. Confirm Capacity Bet & Win 250 n The connector shall be inserted completely. n If the double connector has a lock, lock it at the correct position. n Check if there is any loose wire. n After operation, terminal caps shall be installed securely. n Before connecting a terminal, check for damaged terminal cover or loose negative terminal.
PAGE 6
1. GENERAL INFORMATION n After clamping, check each wire to make sure it is secure. Bet & Win 250 n Route harnesses so they are neither pulled tight nor have excessive slack. Do not pull too tightð n Do not squeeze wires against the weld or its clamp. n Protect wires and harnesses with electrical tape or tube if they contact a sharp edge or corner. n After clamping, check each harness to make sure that it is not interfering with any moving or sliding parts.
PAGE 7
1. GENERAL INFORMATION n After routing, check that the wire harnesses are not twisted or kinked. n Wire harnesses routed along with handlebar should not be pulled tight, have excessive slack or interfere with adjacent or surrounding parts in all steering positions. Bet & Win 250 n Symbols: The following symbols represent the servicing methods and cautions included in this service manual.
PAGE 8
1. GENERAL INFORMATION Bet & Win 250 TORQUE VALUES STANDARD TORQUE VALUES Item 5mm bolt, nut 6mm bolt, nut 8mm bolt, nut 10mm bolt, nut 12mm bolt, nut Torque (N-m) 4.9 9.8 21.6 34.3 53.9 Item 5mm screw 6mm screw, SH bolt 6mm flange bolt, nut 8mm flange bolt, nut 10mm flange bolt, nut Torque (N-m) 3.9 8.8 11.8 26.5 39.2 Torque specifications listed below are for important fasteners.
PAGE 9
1.
PAGE 10
1.
PAGE 11
1. GENERAL INFORMATION Bet & Win 250 FRAME The following is the lubrication points for the frame. Use general purpose grease for parts not listed. Apply clean engine oil or grease to cables and movable parts not specified. This will avoid abnormal noise and rise the durability of the motorcycle.
PAGE 12
1.
PAGE 13
1.
PAGE 14
1.
PAGE 15
1. GENERAL INFORMATION Oil Vapor Recovery Tube Bet & Win 250 Fuel Tube T.P.
PAGE 16
1. GENERAL INFORMATION Throttle Cable Bet & Win 250 Ignition Coil Auto Bystarter Spark Plug Cap Fuel Pump Vacuum Tube Carburetor Oil Vapor Recovery Tube Fuel Tube Thermostat Starter Relay T.P.
PAGE 17
1.
PAGE 18
1.
PAGE 19
1.
PAGE 20
1. GENERAL INFORMATION Bet & Win 250 POOR PERFORMANCE (ESPECIALLY AT IDLE AND LOW SPEEDS) Inspection/Adjustment Symptom Probable Cause Check ignition timing Correct timing Incorrect timing Correctly adjusted Incorrectly adjusted ÅFaulty CDI unit ÇFaulty A.C.
PAGE 21
1. GENERAL INFORMATION Bet & Win 250 POOR PERFORMANCE (AT HIGH SPEED) Inspection/Adjustment Symptom Probable Cause Check ignition timing ÅFaulty CDI unit ÇFaulty A.C.
PAGE 22
1.
PAGE 23
1.
PAGE 24
1. GENERAL INFORMATION Bet & Win 250 STARTER MOTOR 1.
PAGE 25
1.
PAGE 26
1.
PAGE 27
1. GENERAL INFORMATION Bet & Win 250 FUEL GAUGE 1.
PAGE 28
1.