FS-C5100DN FS-C5200DN FS-C5300DN Operation Guide
Contents 1 Machine Parts Components at the Front of the Printer ................................... 1-2 Components at the Left of the Printer ...................................... 1-2 Internal Components .................................................................. 1-3 Components at the Rear of the Printer ..................................... 1-3 Operation Panel ..........................................................................
iv
Legal and Safety Information CAUTION NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION. Notice on Software SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is factory-set to emulate the PCL. Notice The information in this guide is subject to change without notification. Additional pages may be inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
License Agreements IBM Program License Agreement THE DEVICE YOU HAVE PURCHASED CONTAINS ONE OR MORE SOFTWARE PROGRAMS (“PROGRAMS”) WHICH BELONG TO INTERNATIONAL BUSINESS MACHINES CORPORATION (“IBM”). THIS DOCUMENT DEFINES THE TERMS AND CONDITIONS UNDER WHICH THE SOFTWARE IS BEING LICENSED TO YOU BY IBM. IF YOU DO NOT AGREE WITH THE TERMS AND CONDITIONS OF THIS LICENSE, THEN WITHIN 14 DAYS AFTER YOUR ACQUISITION OF THE DEVICE YOU MAY RETURN THE DEVICE FOR A FULL REFUND.
3. Limitation of Remedies IBM's entire liability under this license is the following; For any claim (including fundamental breach), in any form, related in any way to this license, IBM's liability will be for actual damages only and will be limited to the greater of: 1 the equivalent of U.S.
Monotype Imaging License Agreement 1 “Software” shall mean the digitally encoded, machine readable, scalable outline data as encoded in a special format as well as the UFST Software. 2 You agree to accept a non-exclusive license to use the Software to reproduce and display weights, styles and versions of letters, numerals, characters and symbols (“Typefaces”) solely for your own customary business or personal purposes at the address stated on the registration card you return to Monotype Imaging.
12 You shall not sublicense, sell, lease, or otherwise transfer the Software and/or Typefaces without the prior written consent of Monotype Imaging. 13 Use, duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 252-227-7013, subdivision (b)(3)(ii) or subparagraph (c)(1)(ii), as appropriate.
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT "AS IS" AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Compliance and Conformity FCC statement (for users in the United States) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Cautionary Labels The printer bears any of the following labels. For Europe, Asia, and other countries For U.S.A.
Ozone concentration The printers generate ozone gas (O3) which may concentrate in the place of installation and cause an unpleasant smell. To minimize the concentration of ozone gas to less than 0.1 ppm, we recommend you not to install the printer in a confined area where ventilation is blocked. Declaration of Conformity for U.S.A. Model name: Color Page Printer FS-C5100DN/FS-C5200DN/ FS-C5300DN Trade name: Kyocera Mita Responsible party: Kyocera Mita America, Inc.
Declaration of Conformity (Australia) Manufacturer: Kyocera Mita Corporation Tamaki Plant Manufacturer’s address: 704-19, Nojino, Tamaki-cho, Watarai-gun, Mieken 519-0497, Japan declares that the product Product name: Color Page Printer Model name: FS-C5100DN/FS-C5200DN/FS-C5300DN Description of devices: This Page Printer Model FS-C5100DN is the 21 ppm, FS-C5200DN is the 21 ppm, FS-C5300DN is the 26 ppm (monochrome/color), A4 size and utilized plain paper; dry toner; etc.
Energy Saving Control Function The device comes equipped with a Low Power Mode where energy consumption is reduced after a certain amount of time elapses since the device was last used, as well as a Sleep Mode where printer functions remain in a waiting state but power consumption is still reduced to a minimum when there is no activity with the device within a set amount of time. Low Power Mode The device automatically enters Low Power Mode when 10 minutes have passed since the device was last used.
FS-C5100DN FS-C5200DN FS-C5300DN Initial Auto Sleep Setting 5 minutes (60 minutes) 5 minutes (60 minutes) 15 minutes (60 minutes) Power consumption in Auto Sleep 16W (45W) [for USA and Canada] 16W (45W) [for Europe, Asia, and other countries] 15W (45W) [for USA and Canada] 19W (45W) [for Europe, Asia, and other countries] 18W (70W) [for USA and Canada] 21W (70W) [for Europe, Asia, and other countries] ( ): ENERGY STAR program guideline Group for Energy Efficient Appliances (GEEA) The goal of GEE
Installation Precautions Environment CAUTION Avoid placing the printer on or in locations which are unstable or not level. Such locations may cause the printer to fall. This type of situation presents a danger of personal injury or damage to the printer. Avoid locations with humidity or dust and dirt. If dust or dirt becomes attached to the power plug, clean the plug to avoid the danger of fire or electrical shock.
Power Supply/Grounding the Printer WARNING Do not use a power supply with a voltage other than that specified. Avoid multiple connections in the same outlet. These types of situations present a danger of fire or electrical shock. Plug the power cord securely into the outlet. If metallic objects come in contact with the prongs on the plug, it may cause a fire or electric shock.
Precautions for Use Cautions when Using the Printer • Do not place metallic objects or containers with water (flower vases, flower pots, cups, etc.) on or near the printer. This type of situation presents a danger of fire or electrical shock should they fall inside. • Do not remove any of the covers from the printer as there is a danger of electrical shock from high voltage parts inside the printer. • Do not damage, break or attempt to repair the power cord.
Other Precautions • Do not place heavy objects on the printer or cause other damage to the printer. • Do not open the top/left/rear cover, turn off the main switch, or pull out the power plug during printing. • During printing, some ozone is released, but the amount does not cause any ill effect to one's health. If, however, the printer is used over a long period of time in a poorly ventilated room or when printing an extremely large number of copies, the smell may become unpleasant.
About the Operation Guide This Operation Guide has the following chapters: Chapter 1 - Machine Parts This chapter explains the names of parts. Chapter 2 - Printing Operation This chapter explains how to print from your workstation. Chapter 3 - Maintenance This chapter explains how to replace the toner container and how to care for your printer. Chapter 4 - Troubleshooting This chapter explains how to handle printer problems that may occur, such as paper jams.
1 Machine Parts This section provides explanations and illustrations for you to determine the parts and their functions. Try to be familiar with the names and functions of these parts for correct use and optimal performance.
Components at the Front of the Printer 1 2 3 4 6 5 1 Operation Panel 2 Front Cover 3 Face-down Tray (Top Tray) 4 MP (Multi-Purpose) Tray 5 Paper Cassette 6 Power Switch Components at the Left of the Printer 10 11 12 13 7 9 8 7 Left Cover 8 Waste Toner Box 9 Main Charger Units on the Drum Units 10 Magenta Toner Container (M) 11 Cyan Toner Container (C) 12 Yellow Toner Container (Y) 13 Black Toner Container (K) 1-2 Machine Parts
Internal Components 15 14 14 Paper Transfer Unit 15 Envelope Switch Components at the Rear of the Printer 16 22 17 18 19 20 21 16 USB Memory Slot 17 Power Cord Connector 18 Option Interface Slot 19 Network Interface 20 Network indicators 21 USB Interface 22 Rear Cover Machine Parts 1-3
Operation Panel 23 24 25 26 27 28 30 31 29 23 Message Display 24 Ready Indicator 25 Data Indicator 26 Attention Indicator 27 Arrow Key 28 [MENU] Key 29 [OK] ([ENTER]) Key 30 [GO] Key 31 [CANCEL] Key 1-4 Machine Parts
2 Printing Operation This chapter contains explanations on the following topics: Changing Network Interface Parameters Printing a Network Interface Status Page Loading Printer Driver Printing from Application Software Printing Operation 2-2 2-9 2-11 2-14 2-1
Changing Network Interface Parameters This printer supports TCP/IP, TCP/IP (IPv6), NetWare, AppleTalk, IPP, SSL Server and IPSec protocols (For details see Advanced Operation Guide.) TCP/IP, TCP/IP (IPv6) settings Network >TCP/IP Off > > >TCP/IP (IPv6) > Off 2-2 1 2 Press [MENU]. 3 Press Z. Each time you press U or V, the selection changes. Refer to the explanations below when specifying the settings. Press U or V repeatedly until Network > appears.
TCP/IP >TCP/IP On > >>DHCP Off 1 This section describes how to enable the TCP/IP protocol. If TCP/IP is set to Off, use U or V to select On and press [OK] ([ENTER]). 2 Press Z. Each time you press U or V, the selection changes. 3 Display the item you want to set and press [OK] ([ENTER]). A blinking question mark (?) appears while you are setting DHCP and Bonjour. A blinking cursor (_) appears while you are setting IP Address, Subnet Mask and Gateway.
TCP/IP (IPv6) >TCP/IP (IPv6) > On >>ICMPv6(NDP) Off 1 This section describes how to enable the TCP/IP (IPv6) protocol. If TCP/IP (IPv6) is set to Off, use U or V to selecto On and press [OK] ([ENTER]). 2 Press Z. Each time you press U or V, the selection changes. 3 Display the item you want to set and press [OK] ([ENTER]). A blinking question mark (?) appears while you are setting ICMPv6(NDP) and DHCPv6. A blinking cursor (_) appears while you are setting Prefix Length.
3 Press Z. Each time you press U or V, the selection changes. Refer to the explanations below when specifying the settings. ID _ If you are using NetWare, AppleTalk, IPP, SSL Server or IPSec to connect to a network, you must enter an administrator ID. By default, the administrator ID is 000000. For details, see "Admin (Administrator Settings)" in the Advanced Operation Guide.
NetWare >NetWare On >>Frame Type Auto >>Frame Type ?Auto > 1 This section explains the procedure for enabling NetWare. Enter the administrator ID and password. Then, if NetWare is set to Off, use U or V to select On and press [OK] ([ENTER]). 2 Press Z. 3 Press [OK] ([ENTER]). A blinking question mark (?) appears. Each time you press U or V, the selection changes. 4 5 Display the item you want to set and press [OK] ([ENTER]). >>Frame Type ?802.
AppleTalk >AppleTalk On >AppleTalk ?On 1 This section explains the procedure for enabling AppleTalk. Enter the administrator ID and password. Then, if AppleTalk is set to Off, use U or V to select On. 2 Press [OK] ([ENTER]). A blinking question mark (?) appears. 3 4 Press [OK] ([ENTER]) again. Press [MENU]. The display returns to Ready. IPP >IPP On >IPP ?On Printing Operation 1 This section explains the procedure for enabling IPP. Enter the administrator ID and password.
SSL Server >SSL Server On >>DES Off > 1 This section explains the procedure for enabling SSL Server. Enter the administrator ID and password. Then, if SSL Server is set to Off, use U or V to select On and press [OK] ([ENTER]). 2 Press Z. Each time you press U or V, the selection changes. 3 Display the item you want to set and press [OK] ([ENTER]). A blinking question mark (?) appears. 4 5 6 Select On or Off using U or V.
Printing a Network Interface Status Page You can print out a status page for the network interface. The network status page shows the network addresses, and other information under various network protocols about the network interface card. The default setting is Off (print disable). Adjust/Maintenance Adjust/Maintenance is used to adjust the print quality and to carry out printer maintenance.
