User's Manual
Table Of Contents
- Introduction
- FCC statement
- Interface connectors
- Safety information
- IMPORTANT SAFEGUARDS
- Declaration of Conformity (U.S.A.)
- CE Marking Directive
- Declaration of Conformity (Australia)
- Canadian Department of Communications compliance statement
- ISO 7779
- Disclaimer
- Prolonged Non-Use and Moving the Printer
- ENERGY STAR
- The action program Energy 2000
- Kyocera ECO-PRODUCT
- Introduction
- Table of Contents
- Chapter 1 Installing the Printer
- 1.1. Positioning the Printer
- 1.2. Unpacking and Inspection
- 1.3. Names of Parts
- 1.4. Setting Up and Interfacing
- 1-Open the top cover
- 2-Install the toner container
- 3-Close the top cover
- 4-Install the waste toner bottle
- 5-Adjusting the paper guides in the cassette and adding paper
- 6-Open the paper stopper on the face-down output tray
- 7-Install the face-up output tray (if required)
- 8-Connect the printer to the computer
- 9-Attach the power cord
- 10-Print a status page
- 11-Test the interface with the computer
- 12-Set the emulation mode
- 13-Install the printer driver
- 1.5. MP (Multi-Purpose) Tray Feeding
- 1.6. Memory Card
- 1.7. Memory Expansion Installation
- Chapter 2 Operating the Laser Printer
- 2.1. Control Panel
- 2.2. Operating Procedures
- 2.3. Using the Mode Select Menu
- 2.4. Configuring Interfaces
- 2.5. RAM DISK
- 2.6. Operating a Memory Card
- 2.7. Setting Custom Sizes
- 2.8. Setting the Paper Type
- 2.9. Sleep (Ecopower) Mode
- 2.10. Dumping Received Data
- 2.11. KIR 2 Level
- 2.12. Ecoprint Mode
- 2.13. Resource Protection
- 2.14. Adjusting the Print Density
- 2.15. Setting the Audio Warning (Buzzer)
- Chapter 3 Fonts
- Chapter 4 Maintenance
- Chapter 5 Troubleshooting
- Appendix A Printer Specifications
- Appendix B Paper Selection
- Appendix C Host Computer Interface
- Index
- Mode Select Menu
Introduction
xi
As an E
NERGY
S
TAR
Partner, Kyocera Corporation has determined that this
product meets the E
NERGY
S
TAR
guidelines for energy efficiency.
E
NERGY
S
TAR
®
The basic objective of the E
NERGY
S
TAR
Program is to reduce environmental pollution by encouraging the
manufacture and sale of equipment that uses energy more efficiently.
This printer is equipped with a sleep timer function that conforms with the standards of the E
NERGY
S
TAR
Program. This function makes it possible to reduce the amount of electrical power consumed by the printer.
For maximum power savings, turn off the printer's power supply when not using the printer for extended
periods of time.
For details on the sleep timer function and printer power consumption, refer to the instruction manual pro-
vided with the printer.
Initial settings of the sleep timer function and power saved using the sleep timer
function:
(): E
NERGY
S
TAR
program guideline
The action program Energy 2000
Energy partnership for a sustainable development.
We get further – with all our energy.
Kyocera ECO-PRODUCT
This product has been developed and manufactured with the express inter-
est of reducing the impact on the environment.
Using Kyocera's innovative cartridge free technology, Kyocera has created
an advanced printing system that does not require the wasteful replacement
and disposal of a cartridge.
Initial sleep mode setting
Power consumption in
sleep mode
FS-1750 30 minutes (30 minutes) 14 W (30 W)
FS-3750 30 minutes (60 minutes) 16 W (45 W)