User's Manual
Table Of Contents
- Introduction
- FCC statement
- Interface connectors
- Safety information
- IMPORTANT SAFEGUARDS
- Declaration of Conformity (U.S.A.)
- CE Marking Directive
- Declaration of Conformity (Australia)
- Canadian Department of Communications compliance statement
- ISO 7779
- Disclaimer
- Prolonged Non-Use and Moving the Printer
- ENERGY STAR
- The action program Energy 2000
- Kyocera ECO-PRODUCT
- Introduction
- Table of Contents
- Chapter 1 Installing the Printer
- 1.1. Positioning the Printer
- 1.2. Unpacking and Inspection
- 1.3. Names of Parts
- 1.4. Setting Up and Interfacing
- 1-Open the top cover
- 2-Install the toner container
- 3-Close the top cover
- 4-Install the waste toner bottle
- 5-Adjusting the paper guides in the cassette and adding paper
- 6-Open the paper stopper on the face-down output tray
- 7-Install the face-up output tray (if required)
- 8-Connect the printer to the computer
- 9-Attach the power cord
- 10-Print a status page
- 11-Test the interface with the computer
- 12-Set the emulation mode
- 13-Install the printer driver
- 1.5. MP (Multi-Purpose) Tray Feeding
- 1.6. Memory Card
- 1.7. Memory Expansion Installation
- Chapter 2 Operating the Laser Printer
- 2.1. Control Panel
- 2.2. Operating Procedures
- 2.3. Using the Mode Select Menu
- 2.4. Configuring Interfaces
- 2.5. RAM DISK
- 2.6. Operating a Memory Card
- 2.7. Setting Custom Sizes
- 2.8. Setting the Paper Type
- 2.9. Sleep (Ecopower) Mode
- 2.10. Dumping Received Data
- 2.11. KIR 2 Level
- 2.12. Ecoprint Mode
- 2.13. Resource Protection
- 2.14. Adjusting the Print Density
- 2.15. Setting the Audio Warning (Buzzer)
- Chapter 3 Fonts
- Chapter 4 Maintenance
- Chapter 5 Troubleshooting
- Appendix A Printer Specifications
- Appendix B Paper Selection
- Appendix C Host Computer Interface
- Index
- Mode Select Menu
Introduction
i
Caution
NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.
Notice on Software
SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION MODE. The printer is
factory-set to emulate the PCL 6. The emulation mode can be changed by following the procedures described in Chapter
2.
Notice
The information in this manual is subject to change without notification. Additional pages may be inserted in future
editions. The user is asked to excuse any technical inaccuracies or typographical errors in the present edition.
No responsibility is assumed if accidents occur while the user is following the instructions in this manual. No responsi-
bility is assumed for defects in the printer's firmware (contents of its read-only memory).
This manual, any copyrightable subject matter sold or provided with or in connection with the sale of the page printer,
are protected by copyright. All rights are reserved. Copying or other reproduction of all or part of this manual, any
copyrightable subject matter without the prior written consent of Kyocera Corporation is prohibited. Any copies made
of all or part of this manual, any copyrightable subject must contain the same copyright notice as the material from which
the copying is done.
Regarding Tradenames
PRESCRIBE is a registered trademark of Kyocera Corporation. PRESCRIBE 2e, KPDL, and KIR2 (Kyocera Image
Refinement 2)* are trademarks of Kyocera Corporation.
Diablo 630 is a product of Xerox Corporation. IBM Proprinter X24E is a product of International Business Machines
Corporation. Epson LQ-850 is a product of Seiko Epson Corporation.
Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company. Centronics is a trade name
of Centronics Data Computer Corp. PostScript is a registered trademark of Adobe Systems Incorporated. Macintosh is
a registered trademark of Apple computer, Inc. AppleTalk is a trademark of Apple Computer, Inc. Microsoft, Windows,
and MS-DOS are registered trademarks of Microsoft Corporation. PowerPC is a trademark of International Business
Machines Corporation. E
NERGY
S
TAR
is a U.S. registered mark.
This Kyocera page printer uses PeerlessPrintXL to provide the HP LaserJet compatible PCL6 language emulation.
PeerlessPrintXL is a trademark of The Peerless Group, Redondo Beach, CA 90278, U.S.A.
This product was developed using the Tornado™ Real Time Operating System and Tools from Wind River Systems.
Contains UFST
™
and MicroType
®
from Agfa Corporation.
*: KIR 2 uses Pixel Magic’s resolution enhancement technology.
Pixel Magic is a trademark of Oak Technology, Inc.
© 1999 by Kyocera Corporation. All rights reserved, Revision 1.5., February 2001