User's Manual
Table Of Contents
- Introduction
- FCC statement
- Interface connectors
- Safety information
- IMPORTANT SAFEGUARDS
- Declaration of Conformity (U.S.A.)
- CE Marking Directive
- Declaration of Conformity (Australia)
- Canadian Department of Communications compliance statement
- ISO 7779
- Disclaimer
- Prolonged Non-Use and Moving the Printer
- ENERGY STAR
- The action program Energy 2000
- Kyocera ECO-PRODUCT
- Introduction
- Table of Contents
- Chapter 1 Installing the Printer
- 1.1. Positioning the Printer
- 1.2. Unpacking and Inspection
- 1.3. Names of Parts
- 1.4. Setting Up and Interfacing
- 1-Open the top cover
- 2-Install the toner container
- 3-Close the top cover
- 4-Install the waste toner bottle
- 5-Adjusting the paper guides in the cassette and adding paper
- 6-Open the paper stopper on the face-down output tray
- 7-Install the face-up output tray (if required)
- 8-Connect the printer to the computer
- 9-Attach the power cord
- 10-Print a status page
- 11-Test the interface with the computer
- 12-Set the emulation mode
- 13-Install the printer driver
- 1.5. MP (Multi-Purpose) Tray Feeding
- 1.6. Memory Card
- 1.7. Memory Expansion Installation
- Chapter 2 Operating the Laser Printer
- 2.1. Control Panel
- 2.2. Operating Procedures
- 2.3. Using the Mode Select Menu
- 2.4. Configuring Interfaces
- 2.5. RAM DISK
- 2.6. Operating a Memory Card
- 2.7. Setting Custom Sizes
- 2.8. Setting the Paper Type
- 2.9. Sleep (Ecopower) Mode
- 2.10. Dumping Received Data
- 2.11. KIR 2 Level
- 2.12. Ecoprint Mode
- 2.13. Resource Protection
- 2.14. Adjusting the Print Density
- 2.15. Setting the Audio Warning (Buzzer)
- Chapter 3 Fonts
- Chapter 4 Maintenance
- Chapter 5 Troubleshooting
- Appendix A Printer Specifications
- Appendix B Paper Selection
- Appendix C Host Computer Interface
- Index
- Mode Select Menu
2.2. Operating Procedures
2-6
2.2. Operating Procedures
Switching Power On
Check that the power cord is securely plugged in at both ends.
Check that the printer is connected to the computer. In switching
power on, the general rule is to switch on printer power first, com-
puter power second.
1.
Push the power switch to the ON ( | ) position.
2.
Wait for the printer to warm up. During warm-up the mes-
sage display indicatesý6HOIýWHVW.
At the end of the warm-up period, the ON LINE indicator lights,
and the message display indicatesý5HDG\. The printer is now
ready to print.
Stack Selection
The STACK key selects the tray to which the printed pages are delivered. The STACK key can be used whenever
the message display indicatesý5HDG\.
Press the STACK key. The selection toggles and is momentarily displayed in the message display as:
)DFHðX Sý WUD\
)DFHðG RZQý WUD\
If you have installed the optional sorter or stacker,ý6RUWHU orý%XONý
VWDFNH U will also be displayed.
The current selection is indicated by a green light on the printer symbol above the
key.
Also, if the printer is being used with the optional sorter or stacker, the destination of the paper from each
can be selected.
Feed Selection
The FEED key selects the paper feed cassette [&DVVHWWH] or MP tray
[03 WUD\] (or the option paper feeder[s], if installed) as the paper source. The
FEED key can be used whenever the message display indicatesý5HDG\ orý$G Gý
SDSHU .
Press the FEED key. The selection cycles and is momentarily displayed in the mes-
sage display as:
&DVVHW WH
õpaper sizeôõpaper typeô
03ý WUD\>MP tray mode@
õpaper sizeôõpaper typeô
If you have installed the optional paper feeder, the cassette in the printer appears on the display as
&DVVHW WHýì, and the cassettes in the paper feeder appear asý&DVVHWWHýë andý&DVVHWWHýê.
Also, if the Envelop Feeder or Bulk Feeder is installed then MP tray is not displayed andý( ) orý%XONý
IHHGHU is displayed instead.
The current selection is indicated by a green light on the printer symbol above the key.
Power Switch