iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Approved Checked Designed Koyama Yamamoto Hirao Reference: Revision: Date: Kyocera Corporation -1- Q38T-EE-001 1.01 June.08.2006 Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Revision Record Revision 1.00 1.01 Author Hirao Miyasaka Kyocera Corporation Date May.10.2006 June.08.2006 Detail First Release Correct some writings -2- Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual CONTENTS Safety Precautions on iBurst Terminal................................ Terminal ................................................................ .......................................................................... .......................................... 4 Chapter 1 Introduction ................................................................ .......................................................................................
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Safety Precautions on iBurst Terminal • Things you must know • • • When using the product, use it correctly according to the safety precautions. The product uses particular radio frequency band tuned for the network operator. The safety precautions, hardware, software, and the design of the product may be changed in the future without any announcement to the customers.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual • For your safety -------- Danger -------( If used improperly, may cause death or serious injury. ) • • • • • • • • • • • • Do not use with an abnormal condition, such as with emission of smoke or odor. It may cause fire or electric shock. Do not insert metal or flammable materials into the product interior through the air vents. Pull out power plug from the outlet in case that foreign material into the product interior.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual ------- Warning -------( If used improperly, may cause disability or physical damage. ) • • • • • • • • • • • • • Do not give a shock strong against the product, such as dropping and throwing. It becomes the cause of failure. Moreover, do not ride on the product. It may become the cause of an injury. Do not put the product under direct sunshine or near equipment with high temperature such as a stove and a heater.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual -------- Caution -------( If treated improperly, the equipment may not perform or work properly. ) • • • • • • • • Do not put the product at low temperature. The product may not function properly. Do not put the product on the top of magnetic objects and places where electromagnetic waves occur.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 1 Introduction This chapter describes what should should be confirmed before using iBurst Terminal. Terminal. 7 Kyocera Corporation -8- Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Components List The table below shows the list of components. Please confirm items in the package. UTD model Component iBurst Terminal AC/DC Adapter Power Cable USB Cable 10-Base-T Ethernet Cable Notes Q’ty Q’ty Unit of UTD model Refer to the pictures shown in next page. Input: 100 - 240V AC/ 50 - 60Hz/ 300mA Output: 9V DC/ 1.2A Cable Length of output side: 2m Length: 2m Type: USB1.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Outlook of iBurst Terminal UTD model Antenna Power switch Back side view Power Indicator Link/Communication Indicator USB port PC Connection Indicator 10Base-T port only on UTD model DC Power Input Kyocera Corporation - 10 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual UTU model Link/Communication Indicator Power Indicator External antenna port USB port Indicators Indicators The table below describes meaning of each indicator.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Requirements on your PC • PC/AT Compatible PC with WindowsXP/2000/Me/98SE; or version 10.1.5 or later version of Mac OS X except Mac Intel model. • 1 USB1.1 port or a later version of USB port. NOTE: • In case of using USB connection. 1 10Base-T Ethernet port or compatible. NOTE: In case of using 10Base-T Ethernet connection with a UTD model.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 2 Setup Procedure This This chapter describes how to install iBurst software, then guides you how to make a network connection so as to use data communication service. Kyocera Corporation - 13 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual iBurst Software Installation Installation This section shows the procedure to install iBurst software on your PC for utilizing iBurst Terminal. The procedure shall be done once before using it. Installation Installation for Windows XP NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you don’t need to install/uninstall any iBurst software.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Select [I accept the terms the license agreement], click the [Next >] button. 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. Kyocera Corporation - 15 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 8. The following dialog window will appear, and installation of software begins. 9. When the installing process finishes, the dialog window shown below will appear. Select “Yes, I want to restart my computer now” and click the [Finish] button in the dialog window. 10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port. The iBurst Terminal will be recognized and will be ready to use automatically.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows 2000 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Terminal Setup starts. Click the [Next >] button. 5.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 18 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. When the installing process finishes, the dialog window shown below will appear. Select [Yes, I want to restart my computer now] and click the [Finish] button in the dialog window. 10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port. The iBurst Terminal will be recognized and will be ready to use automatically. NOTE: If the PC request to restart again, click [Yes] to restart the PC.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows Me Me Since the the installation disk of Windows Me may be be required while driver installation, please prepare the CD or copy the CD into a hard disk in your PC for it. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 21 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. Click the [Finish] button. 10. Click the [OK] button. NOTE: Refer to the 1st article in chapter 6, if you face such symptom described in the attention message. NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you can skip from hear to step 18 and continue from step 19 in this section. You can see indications of the iBurst Terminal over Ethernet.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 12. Select [Specify the location of the driver (Advanced)] and click the [Next >] button in the dialog window. 13. Select [Search for the best driver for your device.(Recommended)], then check [Specify a location] and click the [Browse] button. 14. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. Kyocera Corporation - 23 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 15. Click the [Next >] button. 16. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click the [Next >] button. 17. Click the [Finish] button. Kyocera Corporation - 24 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 18. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. 19. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 20. Click the [Next >] button. Kyocera Corporation - 25 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 21. Click the [Next >] button. NOTE: If the dialog window shown below appears, select [No, the device isn’t in the list] and click the [Next >] button. 22. Select [No, I want to select the hardware from a list], and click the [Next >] button. Kyocera Corporation - 26 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 23. Select [Ports (COM & LPT)], and click the [Next >] button. 24. Click the [Have Disk..] button. 25. Click the [Browse...] button. Kyocera Corporation - 27 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 26. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 27. Click the [OK] button. 28. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button. Kyocera Corporation - 28 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 29. Click the [Next >] button. 30. Click the [Finish] button. 31. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. 32. Turn your PC on again. Kyocera Corporation - 29 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 33. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. NOTE: If the dialog window as shown below appears, click the [Add] button. Kyocera Corporation - 30 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 34. Check [Don’t detect my modem; I will select it from a list], and click the [Next >] button. 35. Click the [Have Disk..] button. 36. Click the [Browse…] button. Kyocera Corporation - 31 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 37. Select [C:\Program Files\iBurst Terminal\bin],and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 38. Click the [OK] button. 39. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button. Kyocera Corporation - 32 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 40. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button. NOTE: The ‘X’ in “COM X” above is a COM port number assigned automatically. NOTE: If the dialog window as shown below appears, type a dummy number in “What are (or city) code are you in now ?” and then click the [Next >] button. 41. Click the [Finish] button. Kyocera Corporation - 33 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 42. Click the [OK] button. 43. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation - 34 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 44. Click the [Add…] button on [Configuration] tab. 45. Select [Protocol] and click the [Add…] button. 46. Click the [Have Disk…] button. Kyocera Corporation - 35 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 47. Click the [Browse…] button. 48. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 49. Click the [OK] button. Kyocera Corporation - 36 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 50. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button. NOTE: If the same dialog at step 46 is popped up again, cancel once and repeat from step 44. 51. Click the [OK] button. NOTE: For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> iBurst Terminal” must be added automatically.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 52. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. NOTE: To connect to the Internet, refer to page 67. Kyocera Corporation - 38 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows 98SE Since the the installation disk of WINDOWS 98SE may be required while driver installation, please prepare the CD or copy the CD into a hard disk in your PC for it. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 40 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. Click the [Finish] button. 10. Click the [OK] button. NOTE: Refer to the 1st article in chapter 6, if you face such symptom described in the attention message. NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you can skip from hear to step 19 and continue from step 20 in this section. You can see indications of the iBurst Terminal over Ethernet.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 12. Click the [Next >] button in the dialog window. 13. Select [Search for the best driver for your device.(Recommended)], and then check the [Next >] button. 14. Check [Specify a location] and click the [Browse] button. Kyocera Corporation - 42 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 15. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. 16. Click the [Next >] button. 17. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click the [Next >] button. Kyocera Corporation - 43 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM], click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 18. Click the [Finish] button. 19.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 20. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 21. Click the [Next >] button. 22. Click the [Next >] button. Kyocera Corporation - 45 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, select [No, the device isn’t in the list] and click the [Next >] button. 23. Select [No, I want to select the hardware from a list.], and click the [Next >] button. 24. Select [Ports (COM & LPT]], and click the [Next >] button. Kyocera Corporation - 46 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 25. Click the [Have Disk..] button. 26. Click the [Browse…] button. 27. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. Kyocera Corporation - 47 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 28. Click the [OK] button. 29. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button. 30. Click the [Next >] button. Kyocera Corporation - 48 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM],click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 31. Click the [Finish] button. 32.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 33. Turn your PC on again. 34. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. NOTE: If the dialog window as shown below appears, click the [Add] button. Kyocera Corporation - 50 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 35. Select [Other], and click the [Next >] button. 36. Check [Don’t detect my modem, I will select it from a list] and click the [Next >] button. 37. Click the [Have Disk…] button. Kyocera Corporation - 51 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 38. Click the [Browse…] button. 39. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 40. Click the [OK] button. 41. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button. Kyocera Corporation - 52 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 42. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button. NOTE: The ‘X’ in “COM X” above is a COM port number assigned automatically. NOTE: If the dialog window as shown below appears, type a dummy number in “What are (or city) code are you in now ?” and then click the [Next >] button. 43. Click the [Finish] button. Kyocera Corporation - 53 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 44. Click the [OK] button. 45. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation - 54 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 46. Click the [Add] button on [Configuration] tab. 47. Select [Protocol] and click the [Add…] button. 48. Click the [Have Disk…] button. Kyocera Corporation - 55 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 49. Click the [Browse…] button. 50. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 51. Click the [OK] button. Kyocera Corporation - 56 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 52. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button. NOTE: If the same dialog at step 47 is popped up again, cancel once and repeat from step 45. 53. Click the [OK] button. NOTE: For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> iBurst Terminal” must be added in this stage.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM],click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 54.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Mac OS X NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you can skip this section and you need only to create a dial-up connection setting described at from page 69. Please note that you cannot utilize the iBurst utility software described in chapter 3.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 4. In case of version 10.3 or later, the confirmation message shown below will appear. Click [Continue] button. 5. In case of version 10.2 or older, “Authenticate” dialog will appear. Enter an administrator name and password, and then click the [OK] button. 6. Click the [Continue] button. Kyocera Corporation - 60 - Revision 1.01 --- June.08.
