iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 7. Click the [Continue] button. 8. The following dialog will appear, click the [Agree] button. 9. Select a destination disk, and then click the [Continue] button. Kyocera Corporation - 61 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 10. Click the [Install] button after appearing dialog window as shown below. NOTE: In case of version 10.4, Authentication dialog will appear at here. 11. Click the [Continue installation] button. 12. When finish installing, the dialog shown below will appear. Click the [Restart] button. NOTE: To connect to the Internet, refer to page 69. Kyocera Corporation - 62 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Connection Establishment Connection Establishment for Windows XP 1. Make sure to connect the iBurst Terminal with your PC via USB cable or Ethernet cable. 2. Click the [Start] button, followed by selecting [Control Panel] as shown below. 3. Click [Network and Internet Connections] in the [Control Panel] display. 4. Next, click [Set up or Change your Internet connection]. Kyocera Corporation - 63 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. When the [Internet Properties] dialog window appears, click the [Setup] button. 6. [New Connection Wizard] will begin and the dialog window as shown below will appear. Click the [Next >] button in the dialog window. 7. Select [Connect to the Internet] and click the [Next >] button. Kyocera Corporation - 64 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 8. Select [Set up my connection manually] and click the [Next >] button. 9. Select [Connect using a broadband connection that requires a user name and password] and click the [Next >] button. 10. Fill in [ISP Name] edit box with an ISP Name, followed by clicking the [Next >] button. Note that any ISP name is acceptable. ISP Name is “iBurst” for example. Kyocera Corporation - 65 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 11. Enter user name and password and make sure that the [Make this the default Internet connection] check box is checked. Click the [Next >] button. Check it if you want. Nothing in case SP2 of Windows XP. 12. Click the [Finish] button. Check it if you want. 13. When the [Network and Internet Connection] window pane appears again, click [Set up change your Internet Connection]. Kyocera Corporation - 66 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 14. When the [Internet Properties] dialog window appears and the [Connections] pane is displayed, confirm the connection name and make sure that the [Always dial my default connection] radio button is checked, followed by clicking the [Apply] button. Then, click the [OK] button to close the dialog window. The ISP name specified at step 10 above must be the default connection. iBurst (Default) Select “Always dial ...”. 15.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Connection Establishment for Windows 2000/Me/98SE NOTE: You have to execute the procedure in this section every when you want to connect to the Internet. 1. Make sure to connect the iBurst Terminal with your PC via USB cable or Ethernet cable.. 2. Double click the shortcut icon on the PC desktop; or click [Start] -> [Programs] -> [iBurst Terminal] -> [iBurst_Terminal Connect UTL] 3. Enter user name and password and click the [Connect] button.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 4. While connecting to network, the following connection status window is displayed. 5. When logging on successfully, a network connection icon will be displayed at the task tray. Kyocera Corporation - 69 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Connection Establishment for Mac OS X 1. Make sure to connect the iBurst Terminal with your PC via USB cable or Ethernet cable. 2. Select [System Preferences…] on the Apple menu. 3. Click [Network] in the [System Preferences] window. 4. After the 1st connection with the iBurst Terminal via USB cable, you will find the pop-up shown below. Take note the name of the new port. Click [OK]. X) Kyocera Corporation - 70 - Revision 1.01 --- June.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Click on the drop down menu of the [Show]; and Select [Ethernet Adaptor (en X)] indicated in the previous step in case of USB connection; or Select appropriate “Ethernet” interface in case of Ethernet connection, “Built-in Ethernet” for example. NOTE: The ‘X’ in the “en X” is the port number and it shall be the biggest one among them when 1st connection. Additionally, set as follows. • Select the [PPPoE] tab. • Check [Connect using PPPoE].
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. On the PPPoE Options dialog, set everything as follows and click [OK]. NOTE: If you don’t enable “Connect automatically when needed”, you have to make a PPPoE connection following the procedure described in the next page every when you want to connect to the Internet. 7. Click the [Apply Now] button. X) 8. At this point, the connection configuration is completed. When you open any internet application software, e.g.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: To check the internet connectivity only in case of using a USB cable, follow the steps below. 9. Click the <---> icon at the top right of screen, and select the Ethernet Adapter you choose in step 5. In addition, click <---> again and choose [Open Internet Connect] X) 10. Click on drop down menu of [Configuration], and select [Ethernet Adaptor (en X)].
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 3 Utility Software This chapter describes the features and usage of the Utility Software for iBurst Terminal. Kyocera Corporation - 74 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Using Utility Software Using Utility Software for Windows Windows To open the utility dialog. 1. To open the utility dialog, click the icon on the computer’s task tray; or click [Start] -> [Programs] -> [iBurst Terminal] -> [iBurst_Terminal UTL]. When the dialog opens, the [Link Info] pane will be displayed as shown below. 2.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Link Info Pane [Link Info] pane indicates several communication status about iBurst Terminal. (1) (2) (4) (3) (5) (6) (7) (8) The following descriptions are about each item on the pane. (1) UTID UTID is an identifier assigned to the iBurst Terminal. This will be used for maintenance support. (2) Link Status This indicates current link status between the iBurst Terminal and the access point. Connect : The link is connected.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual (5) Signal Strength This indicates current signal strength of the received radio signal. The signal bar indicates the level visually in percentage and the status words are categorized according to the percent level as follows.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Setup Pane [Setup] pane can be displayed in the main dialog window by clicking the [Setup] tab. This pane controls enabling/disabling to show each indicator on the [Link Info] pane. (2) (1) (4) (3) (6) (5) The following descriptions are about each item on the pane. (1) Selecting [ON] enables the corresponding indicator on the Link Info pane. All are [ON] as the default.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual About Pane [About] pane shows the version information about software, hardware and copyrights. (1) (2) (3) The following descriptions are about each item on the pane. (1) This shows the version number and the build date of this Utility Software. (2) This shows the firmware version and the build date of the iBurst Terminal. (3) This shows the hardware version and the manufactured date of the iBurst Terminal.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Icon Display in task tray When the Utility Software for iBurst Terminal is running, an icon of the Utility Software will be displayed in the task tray of the computer monitor according to communication status of the iBurst Terminal. The table below shows icons with status descriptions. Icon Status of iBurst Terminal iBurst Terminal is not connected with your PC. There is no transmission nor reception on iBurst Terminal.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Using Utility Software for Mac OS X To open the utility dialog. 1. Click the iBurst Terminal UTL icon on the Dock. 2. The iBurst_Terminal UTL dialog appears as shown in next page. Kyocera Corporation - 81 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Link Info Pane [Link Info] pane indicates several communication statuses about iBurst Terminal. (1) (2) (3) (4) (5) (6) (7) (8) The following descriptions are about each item on the pane. (1) UTID UTID is an identifier assigned to the iBurst Terminal. This will be used for maintenance support. (2) Link Status This indicates current link status between the iBurst Terminal and the access point. Connect : The link is connected.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual (5) Signal Strength This indicates current signal strength of the received radio signal. The signal bar indicates the level visually in percentage and the status words are categorized according to the percent level as follows.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Setup Pane [Setup] pane can be displayed in the main dialog window by clicking the [Setup] tab. This pane controls enabling/disabling to show each indicator on the [Link Info] pane. (1) (2) (4) (3) The following descriptions are about each item on the pane. (1) Selecting [ON] enables the corresponding indicator on the Link Info pane. All are [ON] as the default.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual About Pane [About] pane shows the version information about software, hardware and copyrights. (1) (2) (3) 1.0 3/24/06 The following descriptions are about each item on the pane. (1) This shows the version number and the build date of this Utility Software. (2) This shows the firmware version and the build date of the iBurst Terminal. (3) This shows the hardware version and the manufactured date of the iBurst Terminal.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Menu Bar It will be displayed while the iBurst Terminal utility is active. (1) iBurst_Terminal UTL menu The menu is used to quit the iBurst Terminal utility or to perform other operations. (2) DisplaySetup menu The menu is used to control enabling/disabling to show each indication on the [Link Info] pane. The function is the same as the [Setup] pane of the dialog. (3) Help menu The [Help] window will appear when help menu is selected.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Icon Display on the Dock When the Utility Software for iBurst Terminal is running, an icon of the Utility Software will be displayed in the task tray of the computer monitor according to communication status of the iBurst Terminal. The table below shows icons with status descriptions. Icon Activities on iBurst Terminal iBurst Terminal is not connected with your PC. iBurst Terminal is connected with your PC, but No Signal received.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Status Indication over Ethernet Introduction In case that you want to make an IP connectivity through Ethernet, not through USB, you can see statuses of iBurst Terminal on a web browser instead of iBurst Utility software. In this case, you need to follow the steps described in this section. Attention Since the Ethernet port of an iBurst Terminal has a fixed IP address, 192.168.250.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 1) Click “Start” -> “Settings” -> “Control Panel” to open that. 2) Double click “Network and Dial-up Connections” to open that. 3) Double click the connection of the Ethernet port you want to use. In general case, the name should be “Local Area Connection”. A properties dialog will appear. 4) On “General” tab in the dialog, select “Internet Protocol (TCP/IP)” and click “Properties” button.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 1) Click “System Preferences” on the dock or click the APPLE icon on the top menu and click “System Preferences…” to open that. 2) Click “Network” icon to open that. 3) At the pull-down menu of “Show:”, select the Ethernet port you want to use. In general case, the name should be “Built-in Ethernet”. 4) Select “PPPoE” tab on the dialog and disable “Connect using PPPoE”. 5) Select “TCP/IP” tab on the dialog.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual [IP Address Setting] This page shows current IP address of the iBurst Terminal. You can change the IP address on this page. To change it, type new IP address and click “Submit” button. The page shown below will be shown. Kyocera Corporation - 91 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual [Link Information] This page indicates similar information described in page 75 of iBurst Terminal utility software. ** All information will be updated every 5 seconds. [Configuration] This page indicates similar information described in page 78 of iBurst Terminal utility software. [Help] This navigates you to see the web pages. Kyocera Corporation - 92 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter Chapter 4 MTU Optimizer Software & Network Property This chapter describes the features and usage of the MTU Optimizer Software for iBurst Terminal. Kyocera Corporation - 93 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual MTU Optimizer Software & Network Property MTU optimizer software measures the optimized packet size between your PC and a HOST. It is recommended to tune MTU size in order to avoid any throughput problem. This function is a part of Kyocera PPPoE dialer and it is available on Windows 98SE, ME and 2000. NOTE: You need to make a Internet connection through the iBurst Terminal prior to start this procedure. 1.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 3. The [MTU Setting] dialog is as follows. 4. There are 2 methods to decide MTU size, i.e. manually or automatically. 5. If you want to change MTU size manually, type a value in the MTU field and click the [Update] button. Your PC may request to restart it. 6. If you want to optimize MTU size automatically, A) type a target URL or an IP address of the HOST, which will be notified by the network operator, and click the [Start] button.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual C) The optimizer will finish automatically with a result of the optimized MTU size in the MTU field. XXX.XXX.XXX.XXX D) Click the [Update] button to memorize into your PC. Your PC may request to restart it. XXX.XXX.XXX.XXX NOTE: ‘Monitor’ to revoke the result and show the current memorized MTU size. 7. Click [Close] to close the dialog. 8. If you updated, you need to restart your PC to take effect. Kyocera Corporation - 96 - Revision 1.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 5 Uninstallation This chapter describes how to uninstall iBurst software. software. Kyocera Corporation - 97 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual iBusrt Software Uninstallation Uninstallation Uninstallation for Windows XP/2000 XP/2000 NOTE: All screen copies in this section are examples on Windows XP. 1. Close all programs that are currently running. 2. Disconnect the iBurst Terminal with your PC. 3. Click the [Start] button, followed by selecting [Control Panel] to open Control Panel, and then double click [Add or Remove Programs]. 4.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Click the [OK] button after appearing dialog window as shown below. 6. The following dialog window will appear, and select to delete or not to delete installation history files before uninstallation, then click the [Next >] button. Selecting “Yes” is recommended. 7. The following dialog window will appear, and uninstallation of software begins. Kyocera Corporation - 99 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 8. Click the [Finish] button after appearing dialog window as shown below. Kyocera Corporation - 100 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Uninstallation for Windows Me/98SE Me/98SE 1. Close all programs that are currently running. 2. Disconnect the iBurst Terminal with your PC. 3. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add/Remove Programs]. 4. Select [iBurst Terminal] software,and click the [Add/Remove] button. Kyocera Corporation - 101 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Click the [OK] button when appearing the message as shown below. 6. The following dialog window will appear, and select to delete or not to delete installation history files before uninstallation, then click the [Next >] button. Selecting “Yes” is recommended. 7. The following dialog window will appear, and uninstallation of software begins. Kyocera Corporation - 102 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 8. Click the [Finish] button after appearing dialog window as shown below. NOTE: In case that the uninstaller shows a selection of restarting your PC, it is recommended to restart it. 9. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [System]. Kyocera Corporation - 103 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 10. Select [iBurst Terminal Virtual MODEM] on [Device Manager] tab, then click the [Remove] button. 11. Click the [OK] button. NOTE: In case Windows 98 SE, no selection is on the dialog. Kyocera Corporation - 104 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 12. Select [iBurst Terminal Virtual COM Port(COMx)] on [Device Manager] tab, then click the [Remove] button. NOTE: The ‘X’ in “COM x” above is a COM port number assigned automatically. 13. Click the [OK] button. NOTE: “COM3” in the picture below is an example. NOTE: In case Windows 98 SE, no selection is on the dialog. Kyocera Corporation - 105 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 14. Click the [Close] button. 15. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation - 106 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 16. Select [NDIS(PPPoE)Usermode I/O Protocol for iBurst Terminal-> xxxxxx] on [Configuration] tab, then click the [Remove] button.(Repeat the above steps if the other [NDIS(PPPoE)Usermode I/O Protocol for iBurst Terminal] components are installed.) 17. Click the [OK] button to close Network dialog. 18. The dialog window shown below will appear, click the [Yes] button, and restart your PC.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Uninstallation for Mac OS X 1. Close all programs that are currently running. 2. Disconnect the iBurst Terminal with your PC. 3. Open the folder [Applications\iBurst Terminal\Uninstall], then double click the script file [uninst_iburst_terminal.command]. 4. The terminal window shown below will appear, Type administrator’s [password] and press [Enter] key. Kyocera Corporation - 108 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Press [y] or [n] key, and Press [Enter] key. 6. Press [y] and [Enter] key to restart your computer. ATTENTION : Don’t change any properties of MAC Terminal while uninstallation. Otherwise you would have a problem on uninstalling of iBurst Terminal software. Kyocera Corporation - 109 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 6 Trouble shooting This chapter describes how to solve the trouble when you use iBurst. Kyocera Corporation - 110 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Windows USB connection with Windows Me/98SE Me/98SE Windows Me/98SE Me/98SE may need a couple seconds or maximally maximally 1 minute to detect iBurst Terminal through USB connection. If you find this phenomenon, you can avoid it by following procedure. 1. Open Network property [Start] -> [Settings] -> [Control Panel] -> [Network]. 2. Select the [TCP/IP->iBurst Terminal] component, then click the [Properties] button.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 3. Open the [IP Address] tab. 4. Select the [Specify an IP address] then type a private IP address (for example: 192.168.250.11) and type 255.255.255.0 on Subnet Mask. Kyocera Corporation - 112 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Click the [OK] button. 6. Click the [Yes] button, and restart your PC. Kyocera Corporation - 113 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Illegal hanghang-up when install iBurst Terminal. Windows 98SE may need a couple minutes to shutdown itself, or may hanghang-up in worst case after iBurst Terminal device driver installation. This case is from Windows OS and competition with other devices. The following gives you the procedure to fix this problem. 1. Open Network property [Start] -> [Settings] -> [Control Panel] -> [System]. 2. Select [Device Manager] tab.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 3. On the [General] tab, check the box labeled the [Disable in this hardware profile], and then click the [OK] button. 4. Connect iBurst Terminal to USB port. 5. On the [General] tab, uncheck the box labeled the [Disable in this hardware profile], and then click the [OK] button. Kyocera Corporation - 115 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Illegal hanghang-up when set up dialer hang--up in worst case after Windows 98SE may need a couple minutes to shutdown itself, or may hang iBurst Terminal Virtual COM Port driver installation. This case is from Windows OS and competition with other devices. The following gives you the the procedure to fix this problem. problem. 1. Open Device Manager [Start] -> [Settings] -> [Control Panel] -> [System] -> [Device Manager]. 2.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 3. On the [General] tab, check the box labeled the [Disable in this hardware profile], and then click the [OK] button. 4. Re-install iBurst Terminal Virtual COM Port driver according to installation procedure, chapter 2 "Installation for Windows 98SE" step 20. 5. On the [General] tab, uncheck the box labeled the [Disable in this hardware profile], and then click the [OK] button. Kyocera Corporation - 117 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual PC hanghang-up when eject iBurst Terminal from Win98 USB port. Windows 98SE basically does not support hot plugplug-out for USB interface. You might find a problem that your PC hanghang-up itself when you eject iBurst Terminal from USB port during PC running. In this case, please don’t running.. don’t eject iBurst Terminal from USB port during PC running You should eject iBurst Terminal from USB port after you shutdown your PC.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Mac Data rate iBurst Terminal would not perform maximum data rate when it connects with Mac PC. This is obviously caused by Mac OS. And typical data rate connecting with Mac is 800Kbps at downlink and 240Kbps at uplink. Kyocera Corporation - 119 - Revision 1.01 --- June.08.
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 7 Information Information Kyocera Corporation - 120 - Revision 1.01 --- June.08.
