Operation Manual
Table Of Contents
- Operation Guide
- CONTENTS
- MAKING FULL USE OF THE COPIER'S ADVANCED FUNCTIONS
- Section 1 IMPORTANT! PLEASE READ FIRST.
- Section 2 NAMES OF PARTS
- Section 3 PREPARATIONS
- Section 4 BASIC OPERATION
- Section 5 OTHER CONVENIENT FUNCTIONS
- 1. Making 2-sided copies from various types of originals [2-sided copy modes]
- 2. Copying two-page originals onto separate sheets [Page separation/Split copy modes]
- 3. Making a margin space on the copies [Margin mode]
- 4. Centering the copy image [Centering/Image shift mode]
- 5. Adding a space next to the copy images for making notes [Memo mode]
- 6. Making copies with clean edges [Border erase modes]
- 7. Fitting the image of either two or four originals onto a single copy page [Combine/Merge Copy modes]
- 8. Printing page numbers on copies [Print page numbers mode]
- 9. Overlaying one image over another [Form overlay mode]
- 10. Making booklets from sheet originals [Booklet/Stitching mode]
- 11. Making booklets from book originals [Book to Booklet mode]
- 12. Automatic sorting of copy sets without the Document Finisher [Sort/Finished mode]
- 13. Auto rotation function
- 14. Auto selection/Filing mode
- 15. Adding a front and/or back cover to your copy sets [Cover mode]
- 16. Original size selection mode
- 17. Feeding paper as a backing sheet for OHP transparencies [Transparency + backing sheet mode]
- 18. Inverting black and white [Invert mode]
- 19. Making mirror image copies [Mirror image mode]
- 20. Making a test copy prior to large volume copying [Proof mode]
- 21. Making more of the same copies after a copy job is finished [Repeat copy mode]
- 22. Copying a large volume of originals in one operation [Batch scanning mode]
- 23. Saving on toner use [Eco print mode]
- 24. Original set direction
- 25. Memorizing frequently used settings [Program function]
- 26. Registration keys
- 27. Easily add covers and insert sheets between various sets of originals in one operation [Job build mode]
- Section 6 DOCUMENT AND OUTPUT MANAGEMENT FUNCTIONS
- Section 7 COPIER MANAGEMENT FUNCTIONS
- Section 8 OPTIONAL EQUIPMENT
- Section 9 TROUBLESHOOTING
- Section 10 MAINTENANCE AND OPERATION INFORMATION
- Appendix: Functions and settings combination chart
- Laser Safety
- KYOCERA MITA EUROPE B.V.
Section 9 TROUBLESHOOTING
9-7
(1) Cautions
* Do not reuse misfed paper.
* If paper is torn during removal, be sure to remove any loose scraps
of paper from inside the copier, or they could cause another misfeed
later.
* Once misfed paper has been removed, warm-up will begin, the
misfeed indication will go out, and the copier will return to the same
settings prior to the misfeed.
* If a misfeed occurs in the Document Finisher, it is not necessary to
add the misfed copy to the other copies that are already ejected into
the tray, as that copy will be automatically made again.
Paper misfeed.
1.Open front cover.
JAM 00
Paper misfeed.
1.Open front cover.
JAM 00
6
1
2
14
35
3. If paper jams
If a paper misfeed occurs, copying will stop and a message will appear on the touch panel about the misfeed. Leave the main switch ON ( | ) and
refer to “(3) Removal procedures” to remove the jammed paper.
Inch specification Metric specification
(2) Misfeed location indicators
Paper misfeed.
1.Open front cover.
JAM 00
WARNING
High voltage is present in the charger section. Take
sufficient care when working in this area, as there is
a danger of electrical shock.
CAUTION
The copier’s fixing unit is extremely hot. Take
sufficient care when working in this area, as there is
a danger of getting burned.
1 Misfeed in a paper feed area (page 9-8)
2 Misfeed in the paper conveyor section (page 9-13)
3 Misfeed in the fixing section or the ejection section (page 9-14)
4 Misfeed in the Duplex Unit (page 9-17)
5 Misfeed in the Document Processor (page 9-19)
6 Misfeed in the optional Document Finisher (page 9-20)