FS-1920IG.
FS-1920IG.book 1 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Caution No liability is assumed for any damage caused by improper installation. Notice on Software Software used with this printer must support the printer’s emulation mode. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by following the procedures described in the Operation Guide contained as an electronic file in the CD-ROM supplied with the printer.
FS-1920IG.book STEP 1 1 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Unpacking Carefully remove the printer and other items from the box. Check that nothing is missing against the list of shipped components below. List of Shipped Components (A) (B) (C) (for U.S.A. only) (D) (E) Printer (F) Printer Waste Toner Box (E) CD-ROMs (B) Installation Guide [this booklet] and other printed matter (B) Toner Container (D) Plastic Bag for Developer Unit (A) Power Cord (F) Dust Cover (C) [for U.S.A.
FS-1920IG.book STEP 2 2 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Positioning the Printer Make sure that the place of installation meets the following requirements: Clearance 30 cm (11-13/16 inches) 20 cm (7-7/8 inches) [40 cm (15-3/4 inches) when the option rear tray is installed] 30 cm (11-13/16 inches) 25 cm (9-7/8 inches) 60 cm (23-5/8 inches) Be sure to secure enough space around the printer. Prolonged use without sufficient clearance may cause heat to build up within the printer, resulting in fire.
FS-1920IG.book STEP 3 3 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Installing the Toner Container Before you can use the printer for the first time, you must prepare it by installing the toner container, waste toner box, and set up the interfacing with the computer. Top Cover 1 Open the printer top cover all the way. 2 Take the toner container from the bag.
FS-1920IG.book 4 ページ ２００４年１月１５日 木曜日 午前１０時２１分 6 Push firmly on the top of the toner container at the positions marked PUSH HERE. When the toner container fits into place, it will lock with a clicking sound. 7 Close the top cover. To remove the toner container Lock Lever 4 Pull the lock lever (blue colored) to the right and gently lift the toner container.
FS-1920IG.book STEP 4 5 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Installing the Waste Toner Box The waste toner box is supplied with the printer. The waste toner box must be installed in the printer. 1 Open the cap of the waste toner box. Cap Waste Toner Box Left Cover 2 Open the left cover on the left side of the printer. 3 Insert the waste toner box as shown in the figure. The box will be locked when it fits into place.
FS-1920IG.book 6 ページ ２００４年１月１５日 木曜日 午前１０時２１分 4 Ensuring that it is correctly inserted, close the left cover. To remove the Waste Toner Box While holding the waste toner box, press the lock lever and then gently remove the waste toner box.
FS-1920IG.book STEP 5 7 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Connecting the Printer to the Computer There are various ways of connecting the printer to the computer, such as through the parallel interface connector, through the USB (Universal Serial Bus) interface connector, through the option serial interface board kit (IB-11) or through the option network interface card. Printer Connections Option Serial Interface Board Kit (3.
FS-1920IG.book 8 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Parallel Interface Connection 1 Plug one end of the printer cable (not included) into the parallel interface connector on the rear of the printer. Clip Parallel Printer Cable Clip • Use a parallel printer cable that complies with the IEEE1284 standards. • The printer will work best if it is installed near the coputer. The connecting cable should be shielded and not be longer than 3 meters (10 feet).
FS-1920IG.book STEP 6 9 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Connecting the Power Cord This section describes the procedure for connecting the power cord and various cautions. Notes on Power Supply • Install the printer near an AC wall outlet, preferably one that can be used for the printer alone. • Only use this printer with the supply voltage indicated on the serial number label attached to the printer’s rear panel.
FS-1920IG.book STEP 7 10 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Adding Paper to the Paper Cassette and MP Tray The paper cassette can accommodate A5 to A4/Letter and Legal (for U.S.A. only) size paper and can hold approximately 500 sheets. The MP (Multi Purpose) tray can accommodate the various paper sizes and can hold approximately 100 sheets of paper. Paper sizes that are not standard sizes (other sizes) but within the size limitations can also be loaded into the cassette.
FS-1920IG.book 11 ページ ２００４年１月１５日 木曜日 午前１０時２１分 1 Pull the paper cassette all the way out of the printer. Paper Cassette 2 Push the bottom plate down until it locks. Bottom Plate Standard paper sizes are attached to the inside of the paper cassette as shown in the following figure. In the paper cassette for U.S.A., Legal size indication is also attached.
FS-1920IG.book 12 ページ ２００４年１月１５日 木曜日 午前１０時２１分 3 Turn the paper size dial so that the size of the paper you are going to use appears in the paper size window. When the paper size dial is set to OTHER the paper size must be set into the printer on the operator panel. See the Operation Guide (PDF file) provided on the CD-ROM. Paper Size Dial Paper Size Window 4 Adjust the position of the paper guides located on the left and right sides of the paper cassette.
FS-1920IG.book 13 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Fan the media (paper/transparencies), then tap it on a level surface to avoid media jams or skewed printing. 6 Slide the paper into the paper cassette. Load Limit Load Limit • Do not load more paper than will fit under the load limits on the paper guides. • The paper cassette will hold approximately 500 sheets of paper with a 80 g/m² (21 lb.) basis weight, or with a thickness of 0.11 mm. 7 Set the stack of paper so that it is under the clips as shown.
FS-1920IG.book 14 ページ ２００４年１月１５日 木曜日 午前１０時２１分 8 Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. Paper Gauge There is a paper gauge on the right side of the front of the paper cassette to indicate the remaining paper supply. When paper is exhausted, the pointer will go down to the level of (empty). 9 If you have installed a paper cassette that can hold the Legal size paper, install the dust cover at the back of the printer.
FS-1920IG.book 15 ページ ２００４年１月１５日 木曜日 午前１０時２１分 MP (Multi Purpose) tray 1 Pull the MP tray towards you until it stops. MP Tray 2 Pull out the subtray. 3 Adjust the position of the paper guides A4 LTR B5 A5 on the MP tray. Standard paper sizes are attached to the MP tray. For standard paper sizes, slide the guides to the position marked correspondingly. Paper Guides Load Limit 4 Align the paper with the paper guides and insert as far as it will go.
FS-1920IG.book 16 ページ ２００４年１月１５日 木曜日 午前１０時２１分 If the paper is considerably curled in one direction, for example, if the paper is already printed on one side, try to roll the paper in the opposite direction to counteract the curl. Printed sheets will then come out flat. Correct Incorrect To Close the MP Tray Before closing the MP Tray, ensure the subtray is pushed back in, and the paper guides are opened as far as they will go.
FS-1920IG.book 17 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Installing the Option Rear Tray Use the rear tray when you wish paper to be stacked with the printed side facing up (reverse order), or when you are printing on envelopes, postcards, transparencies, or thick paper. This rear tray is a separate option.
FS-1920IG.book STEP 8 18 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Turning the Power Switch On This section describes the procedure for turning on the printer’s power. During start-up, the language for the message display and status page of this printer can be selected from English, French, German, Italian, Dutch, Spanish, and Portuguese. The default message language is English. For how to change the message language to another, refer to the Selecting a Message Language section. 1 Switch on the printer’s power.
FS-1920IG.book 19 ページ ２００４年１月１５日 木曜日 午前１０時２１分 3 The message display indication changes to that shown on the left and ? flashes. MSG language ? English 4 Press the or key repeatedly until the message display shows the desired language and then press the ENTER key. or If you do not wish to change the setting, press the CANCEL key. ENTER 5 The READY ( ) indicator on the operator panel lights and the printer gets ready to print.
FS-1920IG.book 20 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Correcting a Paper Jam If a paper jam occurs while you are printing, remove the jammed paper as described below. After you have removed the jammed paper, open and close the top cover or the paper transfer unit. When pulling the paper, pull it gently so as not to tear it. Torn pieces of paper are difficult to remove and may be easily overlooked, deterring the jam recovery.
FS-1920IG.book 21 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Jam Inside the Printer 1 While pulling the paper transfer unit release lever (green colored), pull out the paper transfer unit. 2 If paper is jammed before the registration roller, remove it as shown in A. If paper is jammed under the registration roller, remove it as shown in B.
FS-1920IG.book 22 ページ ２００４年１月１５日 木曜日 午前１０時２１分 FCC statement for users in the United States This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FS-1920IG.book 23 ページ ２００４年１月１５日 木曜日 午前１０時２１分 ■ Caution labels The labels shown are affixed to the printer. Label inside the printer (Laser radiation warning) (European/Pacific countries) (U.S.A/Canada) Label on the printer’s rear panel Label inside the rear Ozone concentration The printers generate ozone gas (O3) which may concentrate in the place of installation and cause an unpleasant smell. To minimize concentration of ozone gas to less than 0.
FS-1920IG.book 24 ページ ２００４年１月１５日 木曜日 午前１０時２１分 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product. 10. Except as explained elsewhere in User’s Manual, do not attempt to service this product yourself. Removing covers may expose you to dangerous voltage points or other risks.
FS-1920IG.book 25 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Declaration of Conformity (Australia) Manufacturer’s name: Manufacturer’s address: Kyocera Mita Corporation, Tamaki Plant 704-19 Nojino, Tamaki-Cho, Watarai-Gun, Mie-Ken 519-0497, Japan declares that the product Product name: Page Printer Model number: FS-1920 (as tested with the enhancement optional units: PF-60, DU-61, and SO-60) Description of device: This Page Printer Model FS-1920 is the 28 ppm; A4 size and utilized plane paper; laser; dry toner etc.
FS-1920IG.book 26 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Prolonged Non-Use and Moving the Printer ■ Prolonged Non-use If you ever leave the printer unused for a long period of time, remove the power cord from the wall outlet. We recommend you consult with your dealer about the additional actions you should take to avoid possible damages that may occur when the printer is used next time. ■ Moving the Printer When you move the printer: • Move it gently.
FS-1920IG.book 27 ページ ２００４年１月１５日 木曜日 午前１０時２１分 4 Push the center as shown in the figure to make space for the developer unit. 5 Put the developer unit into that space. Developer Unit To reinstall the developer unit into the printer, use the reverse procedure of the above. ENERGY STAR® As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency.
FS1920IG1.fm 28 ページ ２００４年１月１５日 木曜日 午後３時４９分 Options The following options are available for the printer. 1 Sorter (SO-60) 2 Rear Tray 1 Sorter (SO-60) Equipped with five trays each with 200 sheets capacity. Performs sorting, collating, and mailbox function. Attaches to the top of the printer. 2 Rear Tray It attaches to the rear of the printer. 3 Network Interface Card Enables printing from multiple computers via a network.
FS1920IG1.fm 29 ページ ２００４年１月１５日 木曜日 午後３時４９分 Regarding Trademarks PRESCRIBE is a registered trademark of Kyocera Corporation. KPDL and KIR (Kyocera Image Refinement) are trademarks of Kyocera Mita Corporation. Hewlett-Packard, PCL, and PJL are registered trademarks of Hewlett-Packard Company. Centronics is a trade mark of Centronics Data Computer Corp. PostScript is a registered trademark of Adobe Systems Incorporated. Adobe and Acrobat are trademarks of Adobe Systems Incorporated. ENERGY STAR is a U.S.
FS-1920IG.book 30 ページ ２００４年１月１５日 木曜日 午前１０時２１分 4. General You may terminate your license at any time. IBM may terminate your license if you fail to comply with the terms and conditions of this license. In either event, you must destroy all your copies of the Program. You are responsible for payment of any taxes, including personal property taxes, resulting from this license. Neither party may bring an action, regardless of form, more than two years after the cause of action arose.
FS-1920IG.book 31 ページ ２００４年１月１５日 This page intentionally left blank.
FS-1920IG.book 32 ページ ２００４年１月１５日 This page intentionally left blank.
FS-1920IG.
FS-1920IG.book 34 ページ ２００４年１月１５日 木曜日 午前１０時２１分 Operator Panel For more details on operating procedures, see the Operation Guide contained as a PDF file in the CD-ROM supplied with the printer. READY GO DATA ? ATTENTION INTERFACE SIZE TYPE CANCEL MENU ENTER Operator Panel Indicator READY DATA ATTENTION Message Display INTERFACE SIZE TYPE Name Description Ready indicator Flashing: Indicates when an error occurs that you can clear by yourself.
