User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 2--11
July 29/03
Automatic Identification System
V
MM
IM
SI
O#
CS
Na
gn
me
De
ET
st
A
esse
:0
:0
00
:S
:L
QA
3
:S
:M
AR
MD
l/Vo
0000
EXAM
AS
D ®
OT
00
y
0
P
A
--
age
0Na
Ma
LE
Ty
00 H
Set u
vS
xD
:U
:0
pe: 0
HMM®
p
ND
.0
FN
00: 0
D
0
Figure 2--5. Vessel Data Setup
2.1.4.2 Channel Management
This screen is designed for the initial setup for the AIS Transponder channel opera-
tion. The L--3 ProTec Transponder will hold up to eight different channel configura-
tions. The user can set these different configurations at the initial setup; however,
the L--3 ProTec Transponder will acquire the data for a new region once it has en-
tered the region.
For the initial setup perform the following:
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select “Edit Chan Mgmt Settings”, and press the
ENT key. The Channel Management Table Entry screen will appear. (Refer to
Figure 2--6.)
(4) Use the up and down arrow keys and the left and right arrow keys to highlight
an entry point, and press the ENT key.
(5) Enter the data, press the ENT key, and move to the next data entry point.
(6) After all of the data is entered for that region, press the FNC key to save the
data.
(7) If another region is required, press the right arrow key to move to the next
screen and repeat steps (4) through (6).
(8) Press the ESC key to return to the System Configuration screen.