User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 2--12
July 29/03
Automatic Identification System
C
NE
SW
:
:
Ch
PL
A:
vl
Sr
FN
c:
C:
MTb
NX
NX
X °
X °
20
:L
87
M
In
¬
tr
Pr
lEn
00
00
.0
.0
B
d:
w0
Tx
nl
v. ®
t
R
M
ry 8
E
E
XX
XX
C
xA
hB
B
MS
Nx
I:
t.
Ac t
X °
X °
00
00
:2
TZ
08
n:
-- --
F
-- --
NC
v
.0
.0
8
--
Bw
Nm
-- --
S
-- --
av
0
--
e
Figure 2--6. Channel Man ag ement Settings Screen
2.1.4.3 Antenna Position
This setup provides for data entry of location of the antenna for each of the GPS an-
tennas required for the system. The ’Int’ refers to the antenna dedicated to the AIS’
internal GPS and the ‘Ext’ refers to the antenna dedicated to the ship’s external
GPS. The screen layout is as follows:
A
IN
EX
T
T
D
S
im
ee
nt en
A:
A:
0
0
en
I
si
TU
na P
B:
B:
on
-- R
s
M
o
0
0
i
.
si t i
C
C
n
13
Me
71
on R
:0
:0
te
D
rs
oc
ef
D:
D:
0
0
Figure 2--7. Antenna Position Screen
To enter the antenna position, perform the following:
(Refer to Figure 2--7 and Figure 2--8)
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select “Antenna Position Setup”, and press the ENT
key. The Antenna Position Reference screen will appear.
(4) Use the up and down arrow keys and the left and right arrow keys to highlight
an entry point, and press the ENT key.
(5) Enter the data, press the ENT key, and move to the next data entry point.
(6) Press the ESC key to return to the System Configuration screen.