User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 2--14
July 29/03
Automatic Identification System
To broadcast a message, perform the following:
(1) Press MSG key.
(2) Verify that they MMSI number is all zeros.
(3) If the MMSI is not all zeros, press the down arrow key until the MMSI is high-
lighted.
(4) Press the ENT key, and enter all zeros for the MMSI number.
(5) Press the down arrow key to highlight “Mode” and press the ENT key.
(6) Using the down arrow key, highlight “Broadcast”, and press the ENT key.
(7) Using the down arrow key, highlight the message portion of the screen, type in
the message.
(8) Press the MSG key to broadcast the message.
Sa
MM
MO
TE
Us
fety
SI
DE
:0
:B
T: EX
eMs
Tex
00
ro
00
ad
NTER
gKe
t
0
c
y
Ent
00
as
0
t
MESS
to
ry F
AGE
Send
or m
HERE
Text
Figure 2--9. Safety Text Message
To review Safety Text Messages that have been received,
perform the following:
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select “View Safety Text Log”, and press the ENT
key. The Safety Text Review screen will appear.
(4) Use the down left and right arrows to view previous or next messages respec-
tively.
(5) Press the ESC key to return to the System Configuration screen.