User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 2--16
July 29/03
Automatic Identification System
To log on perform the following:
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select Logon, and press the ENT key. The System
Password Entry screen will appear.
(4) Press the ENT key, and enter the password, and press the ENT again.
(5) Press the ESC key to return to the System Configuration screen.
To log off perform the following:
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select Logon, and press the ENT key. The user is
now logged off of the AIS Transponder.
Sy
Pas s
Ent e
Us e
st em
wo r d
rP
ESC
Pas
: _______________________
wd t
To C
s
o
o
wo r d
Ena
nt i n
Ent
bl e
ue
ry
Up d t s
Figure 2--11. Password Entry Screen
2.1.4.6 Change Password
NOTE
: Only users with an administrative password can change pass-
words
To change the transponder’s access password, perform the following:
(1) Press the FNC key.
(2) Press the Setup key. The System Configuration screen will appear.
(3) Using the down Arrow key, select Change Password, and press the ENT key.
The System Password Change screen will appear.