User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 3--3
July 29/03
Automatic Identification System
ProTec AIS Installation
3.1. Installation
The L--3 ProTec Transponder has been designed for easy installation into any exist-
ing bridge layout. Figure 3--1 gives a general representation of the system layout.
Installation can be broken down into 5 distinct operations as follows:
F Transponder
F VHF Antenna
F GPS Antenna
F Data Interface
F Powerup and Configuration
Each operation will be discussed in detail below. In regards to 3rd part components
such as VHF and GPS antennas and Gyro interfaces, it is suggested that the
installation procedures suggested by the manufacturer be followed in lieu of these
procedures.
Junction
Box
IEC 61162 HDG, ROT
TRANSPONDER UNIT
IEC 61162 HDG, SOG, COG, ROT, POSN
POSN,SOG,COG
SHIP
SENSORS
(Optional)
RADAR
ECDIS
PIL OT/PC
AIS DATA
AIS DATA
AIS DATA
VHF Antenna
150M---W2VN
GPS
24 VDC
Power
PIL OT/PC
12---24 VDC
(Optional)
communications
Figure 3--1. AIS Transponder Interconnection Diagram