User Manual
Table Of Contents
- ProTec AIS Installation & Operation Manual
- Return Material Policy
- Return of Material Under Warranty
- Table of Contents
- List of Figures
- Figure 1-1 AIS Transponder
- Figure 2-1 AIS Transponder
- Figure 2-2 NAV Display Screens
- Figure 2-3 Own Ship Data Display
- Figure 2-4 System Configuration Screen
- Figure 2-5 Vessel Data Setup
- Figure 2-6 Channel Management Settings Screen
- Figure 2-7 Antenna Position Screen
- Figure 2-8 Antenna Position Measurements
- Figure 2-9 Safety Text Message
- Figure 2-10 Safety Text Review Screen
- Figure 2-11 Password Entry Screen
- Figure 2-12 Password Change Screen
- Figure 2-13 System Alert Screen
- Figure 2-14 Alarm Status Screen
- Figure 2-15 Down-Time Log Screen
- Figure 3-1 AIS Transponder Interconnection Diagram
- Figure 3-2 AIS Transponder O&D Drawing with Optional Trunion Bracket
- Figure 3-3 AIS Transponder O&D Drawing
- Figure 3-4 AIS Transponder Power Cable
- Figure 3-5 Pilot Port Cable
- Figure 3-6 AIS Transponder IEC Cable
- Figure 3-7 IEC Cable Interconnect Diagram
- Figure 3-8 IEC Cable External Wiring Diagram
- Figure 3-9 AIS Transponder Antenna Diagram
- Figure 3-10 AIS Transponder Rear View
- Figure 3-11 AIS Transponder MKD
- Figure 3-12 System Configuration Screen
- Figure 3-13 Vessel Data Setup
- Figure 3-14 Antenna Position
- Figure 3-15 Calculating Antenna Position
- Figure 3-16 Transponder Interconnection Diagram
- List of Tables
- Table 1-1 AIS Parts List
- Table 1-2 Pilot System High-Speed Input Data Formats
- Table 1-3 Pilot System High-Speed Output Data Formats
- Table 1-4 Long Range Input Data and Formats
- Table 1-5 Long Range Output Data and Formats
- Table 1-6 Sensor Input Data and Formats
- Table 2-1 Vessel Type Codes
- Table 2-2 Password Type Menu Screen Access
- Table 3-1 Data Channels
- Table 3-2 IEC Cable and Junction Box Pinouts
- Table 3-3 Vessel Type Codes
- Section 1. AIS Introduction
- Section 2. AIS Operation
- Section 3. AIS Installation
Marine Systems
Aviation Recorders
Rev. 02 Page 3--10
July 29/03
Automatic Identification System
3.1.2.2 Data Cable
Each transponder will come shipped with an 100 inches long IEC data cable (P/N
024--M0088--01) terminated at one end by a J4 connector. (Refer to Figure 3--6,
Figure 3--7 and Figure 3--8.) The IEC data cable is shielded and contains three
smaller diameter cables, each of which is also shielded. Each of these smaller
cables contains three shielded twisted pairs (STP) each and each STP includes a
drain wire. A low speed unidirectional (input only) data channel (4800 kbs) is carried
through one STP, and a high speed bidirectional (input/output) data channel (38400
kbs) will require two pairs.
P1--Connector, Cannon p/n 2PA31P
Metal or metalized plastic backshell,
Cannon p/n DA121073--150 or Equivalent
Thumbscrew, Cannon p/n 250--8501--013
or Equivalent
Cable, ECS p/n 622818
Marker, Brady p/n PWC--PK3
or Equivalent
Pin 1
Pin 10
Pin 31
Pin 22
100 in. ¦ 2in. 2.5 m ¦ .05 m
10 in. ¦ 2in. 25 cm ¦ 5cm
Figure 3--6. AIS Transponder IEC Data Cable