en CONTENTS Pages WARNINGS ………………………………………………………………………. ..3 1 Installation....................................................................................................4 2. Risk of injury...............................................................................................4 3. Electrical Installation...................................................................................4-5 4. Ventilation shaft........................................................................................
en WARNINGS Read the guides before installing and using this appliance. We decline any responsibility for damage or fires caused by the device if the following warning are not observed. Keep these guides with your device. If the device has to be sold or transferred, the new user shall be informed of its operation and any important warnings. This device may not be used by children or disabled persons without the presence of an adult .
en WARNINGS 1. Installation This appliance must be installed by a qualified professional in accordance with the current regulations in the country where the appliance is installed. All installation and connection operations, activation and repairs must imperatively be performed by a qualified technician. The technician will determine the type of wall mounting and the outer ventilation outlet connection adapted to your hood model.
en WARNINGS Cut off the current before performing any electrical interventions on the hood. Ensure that none of the electrical cables are damaged before drilling the mounting holes into the wall or the ceiling. Perform the electrical connection so that you can easily connect the hood. Comply with local directives. 4. VENTILATION SHAFT Never connect a hood to a CMV (Controlled Mechanical Ventilation), central heating or gas heating shaft.
en WARNINGS 5. FIRE HAZARDS To reduce fire hazards, only use metal shafts. The hood can only be installed above a solid fuel fire if the fire is closed by a non-removable cover. Never flambé food under the hood or leave a gas burner alight without a container. Any flames entering the hood may damage the filters and cause a fire. Frying food must be monitored attentively. Overheated oils and greases can catch fire.
en GENERAL INFORNATION 2. TECHNICAL CHARACTERISTICS OF HOOD EQUIPMENT Voltage: 120 V a. c. single-phase + earth / 60 Hz for 1 motor version and 4 LED Lights - Nominal flow: 600 cfm - Electrical power: 460W - Current: 3,8 A Lighting : - light LED - power 2,5 W Filter : - Stainless steel - Dimensions: 300 x 400 mm Control panel inside the hood on the motor speed regulator and light button.
en 3.
en 3.
en 3.
en ASSEMBLY INSTRUCTIONS WARNING Excessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury HOOD WITH EXTERNAL EXTRACTION An assembly jig is attached to the hood for transportation to avoid any damage. To install the hood, you must first remove this jig according to the following indications but, before doing so, you must imperatively prepare the hood support structure according to our instructions.
en ASSEMBLY INSTRUCTIONS 3. Position the assembly jig on the wall. The grooves in the middle of the bars indicate the centre of the hood. Ensure that the assembly jig is horizontal and mark the holes for drilling. Drill the holes indicated on the jig in the wall and insert pegs adapted to the type of wall. Fix the assembly jip into holes C with long screws and into the upper and lower holes (d, D) with the threaded roads supplied with the hood. N.B. The pegs supplied are only suitable for solid materials.
en ASSEMBLY INSTRUCTIONS 5. The mounting lugs allow you to adjust the position (angle) of the hood body in relation to the wall. Choose your version according to the shape of the wall (A, B, or C). The adjusting screws must be blocked with the locknuts. 6. Connect the ventilation shaft to the manifold flange. Please note: The ventilation shaft must not be folded or crushed. Perform the electrical connections. 7.
en ASSEMBLY INSTRUCTIONS 7.2 REMOTE BLOWER INSTALLATION ( 8. Remove the 2 hatches (E) from the sides of the body. 9. Fit the mantel (B) onto the threaded rods (K) using the provide nuts. The hood mantel must not be twisted. Using a 90 degree screwdriver screw the mantel at the Bottom via the hatch and at the top space left vacant for the ferrule. Replace the hatches inside the Body via the filters.
en ASSEMBLY INSTRUCTIONS Please note: If the hood is ordered without a ferrule, before fixing the mantel in place, you must remove the lugs (L) that are designed for fixing the ferrule in place and pull down the guiding lugs (M). 9. Position the hood ferrule (F) in place by sliding it in parallel above The Hood mantel. The two clips on the rear lugs (L) must be inserted into the holes (H) on the ferrule.
en ASSEMBLY INSTRUCTIONS 10. Position the listels (I) on the hood body and fix them in place on the left and right with a M3 screw. Fix the connecting pierce in place (J). 11. Fix the 5-star plate to the listel connecting piece (J) with 3 M3 screws. 12. Position the filters in place and perform an operating test.
en ELECTRICAL DIAGRAM Hood with internal Motor 17
en ELECTRICAL DIAGRAM Hood with external Motor 18
en 19
en 20
INDEX 03 / 15 Artikel Nr.