Installation Guide

ManualsBrandsLa Crosse Technology ManualsGarden CenterJumbo Atomic Digital Wall Clock with Outdoor Temperature

Page | 3 Page | 4

Atomic Digital Wall Clock

Model: 513-1311OTN

DC: 013018

POWER UP

1. Insert 2 new “AAA” batteries into the outdoor sensor. Observe

correct polarity. The red LED will ﬂash when transmitting.

2. Insert 3 new “C” batteries (not included) into the clock.

Observe the correct polarity.

3. Once the sensor is reading to your station, place sensor

outside in a shaded location.

Watch sensor mounting video: http://bit.ly/TH_SensorMounting

TIME ALARM

1. Press the MODE/SET button to view alarm time. The letters

AL will replace the seconds.

2. Hold the MODE/SET button and the Hour will ﬂash.

3. Use the + or - buttons to adjust the hour.

4. Press the MODE/SET button to conﬁrm and move to the

minutes. Minutes will ﬂash.

5. Use the + or - buttons to adjust the minutes.

6. Press the MODE/SET button to conﬁrm and exit.

DEACTIVATE/ACTIVATE ALARM

• Press the AL ON/OFF button to activate the alarm.

• The bell icon will appears when alarm is active.

• Press the ALARM ON/OFF button to deactivate the alarm.

• The bell icon will disappear.

SNOOZE

• When the alarm sounds, press the SNOOZE button to

trigger snooze alarm for 5 minutes.

• The snooze icon Zz will ﬂash above the time.

• The snooze function can be repeated up to seven times.

AAA

D1: Transmission LED

D2: Outdoor Temperature

D3: Battery Compartment

D4: Wall Mount Hole

D5: “RESET”

D6: °C/°F” button

D7: Stand

SETTINGS

• Hold the MODE/SET button to enter the settings menu.

• Press the + or – buttons to adjust the values.

• Press the MODE/SET button to conﬁrm adjustment and move

to the next item.

Settings menu order:

• Hour • Minutes • Seconds • Year • Month/Date (M/D or D/M)

• Month • Date • DST indicator

Note: Weekday will set automatically when Year, Month and

Date are set.

WWVB ATOMIC TIME

IMPORTANT: When the clock is searching for the WWVB Atomic Time

signal, the buttons will not work. To use the buttons simply hold the

- °C/°F button to stop the clock from searching. Buttons will now work.

• Hold the - °C/°F button to start or stop a manual search for the

WWVB Atomic Time signal.

• WWVB Tower Icon will ﬂash when searching.

• For information about WWVB Atomic Time visit:

http://bit.ly/AtomicTime

Note: The atomic clock will search for 1 hour between midnight and

6am until the WWVB time signal is received. After reception, your

clock will only search for the atomic signal after midnight.

12/24 HOUR TIME & TIME ZONE SELECTION

FAHRENHEIT | CELSIUS TEMPERATURE DISPLAY

• Press the + 12/24 button to select 12 hour or 24 hour time.

• Hold the +12/24 button to select the time zone.

• Time zones:

P Paciﬁc

M Mountain

C Central E

E Eastern

• Press the - °C/°F button to change the temperature display from

Fahrenheit to Celsius.

Summary of content (2 pages)

PAGE 1
Atomic Digital Wall Clock POWER UP 12/24 HOUR TIME & TIME ZONE SELECTION 1. Insert 2 new “AAA” batteries into the outdoor sensor. Observe correct polarity. The red LED will flash when transmitting. 2. Insert 3 new “C” batteries (not included) into the clock. Observe the correct polarity. 3. Once the sensor is reading to your station, place sensor outside in a shaded location. Watch sensor mounting video: http://bit.ly/TH_SensorMounting • • • Press the + 12/24 button to select 12 hour or 24 hour time.
PAGE 2
OUTDOOR SENSOR SEARCH & RECEPTION S P E CIFICAT ION S W E’RE HERE TO HEL P ! Hold the SEARCH button to search for the outdoor sensor. Solid icon: Connected to sensor Flashing icon: Searching for sensor Indoor Temperature Range: 32°F to 122°F (0°C to 50°C) Outdoor Temperature Range: -4°F to 122°F (-20°C to 50°C) Transmission Range: over 330 ft. (100 meters) in open air RF 433MHz FI ND FUL L MANUAL S & FAQS UND ER THE S UPPORT TAB AT: http://bit.